Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi,
Im trying " https://github.com/NordicPlayground/fw-nrfconnect-nrf/blob/master/samples/nrf9160/gps/src/main.c " gsp example to check supl(AGPS) to integrate into my application...
Hi,
In-app when you scan for device and after it is found you press the connect and then the notification/permission to pair pops out. Our app developers are saying that...
Hi,
We are using nRF51DK for our development, we have developed Android app for Android smart phone.
When the Nordic BLE device advertising we are trying for BLE connection...
Hi guys,
I'm fairly new to this kind of stuff and I'd appreciate if someone could point me in the direction of how I would go about taking the data being transmitted by...
Hi nordic,
I am using SDK15.0 (NRF52840) to design a watch producation which needs pairing. I have a problem that if NRF52840 (peripheral ) has been paired with a smartphone...
I want to get the RSSI of a connected device. The sequence will be as follows:
int8_t *p_rssi;
uint8_t *p_ch_index;
sd_ble_gap_rssi_start (m_conn_handle, BLE_GAP_RSSI_THRESHOLD_INVALID...
Setup: nRF52840 DK nRF52 SDK v16.0.0 s140 v7.0.1 When I attempt to use the nrf_crypto library for AES 128bit ECB encryption I keep getting
NRF_ERROR_CRYPTO_CONTEXT_NOT_INITIALIZED...
'm sending a publication set message (0x03) from an iOS app to an nRF52840 board using the light server example in the latest SDK. This works and I'm able to receive messages...
Dear All, I would like to know which is the better GPIO configuration to drive a LED for extremely low power consumption. We have a board with nRF52832 SoC with GPIO connected...
Hi,
I have Android (8.1.0), and installed nRF toolbox 2.8.0. To update firmware using .zip file.
The DFU Upload returns error:
Unfortunately, nRF Toolbox has stopped...
The 3GPP Release 14 introduced new, third power class of 14 dBm for NB-IoT devices. Is it possible to assign nRF9160 to operate at the lowest power rating class, the 14 dBm...
Hello everyone,
I am working on a project where I need to interface an NFC reader (trf7970a from TI) to an NRF52840.
I got everything working fine, but I have a major...
Hello,
I am running S140 on an nRF52840 custom board. While doing some power profiling, I noticed a spike of current of ~15mA when going from sleep mode to waking-up due...
I've created read onle characteristic called "log". In main.c i try to update it by calling : ulogd_characteristic_update(&m_ulog_service,Log_Data_arr)
But nothing happens...
