Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
I tested the code below to make the board go to sleep and wake up on each button press. When I start, it draws 30ua, but when I press the button it shoots up to 200ua (a clear...
Hi,
We are developing nrf9160 sensor based product powered by primary battery(non rechargeable). Sensor current consumption is less than 1 mA.
while trying Saft LS14500...
Hello,
How can i put out the received Adv Data on the UART? Currently I get for every advertise packet the BLE_GAP_EVT_ADV_REPORT in my ble_stack_handler. Then i wanted...
I'm using the ble_app_hrs example code and added a new custom services with multiple characteristics . conn.interval 10ms- 15ms and need to get maximum throughput so i set...
I have nRF52840 DK (board PCA10056) . Right now I flashed LED blinking program on nRF52840 DK. It is fine.
Now I want do ADC operation, so I fed some external analog signals...
Hello, I am trying to send and recieve data with the M24C32-FMN6TP 32 Kbit (4K x 8bit) eeprom. My data are arrays with 16bit values and the datasheet says it cannot write...
Hi,
I have nrf9160 dev board.
It seems to me that getaddrinfo() has memory leak. If socket is closed, and call getaddrinfo() to reopen, it returns -10 (memory) error....
i'm looking for support in desinging modules working in zigbee network with driving this network from mobile phone by bluetooth. It has to be multiprotocol system. How should...
Hi,
I was trying to load the sample example code for Assets tracker in SEGGER Embedded Studio for ARM V4.20a but i encountered with some error.
Transcript & Output:- ...
Hi everyone. I've implemented kind of simple FW updater. The purpose is to copy FW from flash (0x0 address, no MBR or SoftDevice) to RAM buffer on node1. than send this FW...
The most recent nRFConnect AppImage version (3.2.0) fails to launch on a Debian system due to chrome-sandbox file permission errors.
Steps to reproduction:
1. In a recent...
I'm using nrf52832 DK and SDK V 15.3 and SoftDevice S132 . I have created a custom services with 5 characteristics. So i want to get maximum throughput so i increased MTU...
Hi
For our semester project, we develop a box that has to reads some parameters from an oil pump system and send data to the cloud. As we wanted to make it independent of...
Hi everyone,
Im looking to put together a security solution consisting of an accelerometer and a proximity beacon. The accelerometer would be installed on gates and authorized...
As part of our evaluation on the Nordic BLE SOC, I want to measure the throughput, range and the power consumption.
Can someone point me to any sample program(s) that I...
