Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
When I am initializing BSD-library with bsd_init(), the function gives me back an value which i can´t find anywhere 0x00008108.
Hopefully you guys could tell me what this...
Are the virtual page sizes only allowed to be 1024 and 2048 for the nRF52840?
// This is a multiple of the physical page size. Is this allowed or not?
// <i> Expressed...
I am attempting to do the assert_tracker example. I have gotten all the code to build through Segger and upload to the DK. The problem is when I'm watching the terminal for...
Hello there,
I want to run Radio Test on one nR52832 based custom board.
I have flashed the example from SDK 15.3 on the custom board using PCA10040.
I have done the...
I am trying to use nRF9160 as ble gateway for uploading data from two nRF52832. I am wondering is it possible? can I connect nRF9160 (one gatt client) to two nRF52832 (two...
Hello,
I have the following problem. I want to create a whitelist using the PM on a manually added peer.
I manually add a peer by adding its GAP address.
Then I try...
Hello!
Like several others on here, I’m trying to make a multilink nus central firmware. My Peripheral devices run the ble_app_uart example, and the central device runs...
Hello everybody !
Here I am designing a system with 3 development boards nrf52832, where a card called "central" is connected to the computer by USB and this board will...
Dear Nordic,
I'm developing an application using the NUS service en SPIM peripheral. Both of these work correctly independently. Now I'm trying to start an SPI transaction...
I'm developing IO-Link driver using UARTE peripherial.
Is it possible to get event on end of transmition with EasyDMA Tx. Event ENDTX is fired before all transmited bytes...
Segger embedded studio V4.18 appears to have a bug when it comes to printing to RTT. When I run the exact same firmware on SES V3.40, everything is printed to the debug window...
Whether I could build BLE_MESH network automatically within some BLE devices without provisioner?e.t I feel it is manual to build BLE_MESH network with the help of provis...
Hello,
for my project, I am using the module BT832A (from Fanstel) that implements the nrf52810. I am using the pin P.021 to drive a switch. The problem is that when I set...
Hello. I have a problem getting a position via GPS. My dev board is placed in a good place, but can't get a position after more than 1 hour.
I am using you new SW version...
I have been using using nRF9160 as ble gateway for uploading data from one nRF52832 and its works well. Now I need to connect more than one nRF52832 devices, has anyone tried...
