Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
Hi
I want to update bootloader.zip file over BLE DFU mode without signature checking , the open bootloader example only for USB,
How to disable bootloader signature checking...
when message relay by any node how can other node know that it is for him and update status.
for example if I subscribe some nodes to 0xc001 group and others to 0xc002 group...
Hello,
I am making a PCB for my project using the nRF51822 chip? Can I power a LED with the GPIO pin or do I need to connect a MOSFET to drive the current? Also, I want...
Hello everyone, the sdk version that I use is 15.0. The soft device is s132.
With the example of peripheral/uart I am able to receive the serial uart sensor data. On the...
hi,
I'm trying to merge the the proxy server and beaconing example together. When I compare two main.c and copy the advertising part from beaconing to proxy server example...
Hello everyone, the sdk version that I use is 15.0. The soft device is s132.
With the example of peripheral/uart I am able to receive the serial uart sensor data. On the...
Hi Sir
I'd want to send DTM command by hard code, but I don't know where is the command spec for reference ?
Has any one could show me where is the spec ? and give me...
Hi,
I am using nrf52832 with soft device 3. I am operating on peripheral role, while i am initiating sd_ble_gattc_exchange_mtu_request with desired MTU ,it internally sends...
Hi! I am using SDK15.0 and SD 132 v6.0.0. My IDE is Segger Embedded Studio.
Everything was working fine and then suddenly after few weeks of developing a problem appeared...
Testing BLE mesh of proxy light switch example with 3 nrf52840(1 as client and 2 as servers) pdk boards with nrf mesh apk(android phone). Phone able to scan nrf 52840 light...
Dear Team,
I am using ST-Link V2 connector to program a nRF52840 board. When connected to a laptop and try to connect to the target, it says 'ST Link USB Communication...
I am currently trying to extend the range of the bluetooth mesh application. The infocentre infers that the function:
typedef struct
120 {
121 radio_tx_power_t tx_power;...
Hi,
I wonder if someone can make recommendations for types of 'smart bracelet' ('smart wristband') devices that use a BLE chip of Nordic's nRF51/nRF52 range. Can you point...
Hi,
I'm currently developing software on nrf52832. Unfortunately, I can't use the SDK for different reasons.
I'm currently looking at the RESETREAS register. If I...
