Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I have code running on a nRF52 device, with SoftDevice enabled, based on the example given in this topic:
devzone.nordicsemi.com/.../
This runs fine on its own, and...
Hello !
I am currently working on a custom board on which I don't need 32.768kHz. I want to use P0_1 as an interruption pin connected to a pushbutton. The button is connected...
Hi,
I am using IAR embedded version 7.40 and my board is nRF52840 PCA10056,while i was checking devices list in IAR IDE under NordicSemi i can see only nRF51 series devices...
Hey .My source code was compiled against SDK 8.0 now we need to upgrade the SDK to 10.0.
I have just copied the SDK10.0.0"components" folder to my project ( replaced the...
main.c
y_timer.c
y_timer.h
Hi,
I wanted to make the function that get timestamp like mills().
I made this code bellow.
It does'nt move well.
Main loop is unintentionally...
Hi,
During testing I noticed rare BLE connection loses with Softdevice S110 when timeslot session is active. It is hard to catch them with sniffer due to rare behaviour....
I am trying to get the example examples/ble_peripheral/ble_app_template to work from nRF5_SDK_13.1.0.
nRF52832, s132, pca10040
Much of the code works, but inside peer_manager_init...
The device use SDK9.0,during the using of device,when disconnect the bluetooth of phone system sometimes,the system halted.
So I make an experiment about the probability...
Hello,
I am trying the Thread Cloud COAP Client
<InstallFolder>\examples\thread\experimental\cloud_coap_client
on a NRF52840 PDK. I'm using Thread SDK v0.10...
I have troubles with connection using nrf51822 and android phones:
First I connect and bond the device to the phone and it works ok.
Then I periodically...
Hiya,
Regarding voltage amplitude peak to peak for external high-swing clock HFXO 32MHz, what's supply rails？I don't find out this specification defined in datasheet PS_V1...
My phone is like beacon that transmit service data.
(I checked service data in different phone.)
scandata.png
So, I want to recieve service data, service UUID with...
Hello,
I am really new to the field, I apologise, if things I am saying do not make sense, explanations and corrections appreciated :) I am trying to reach IPv4 internet...
Hello,
I would like to make use of an external ADC that is connected to my nRF52832 through SPI & easyDMA,minimizing the use of the CPU (or without using the CPU).
The...
