Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
I have a question about Nordic's implementation of FreeRTOS. In the FreeRTOSConfig.h the following is defined as:
/* The highest interrupt priority that can be used by...
I have a star network that works faithfully in no ACK way, using only pipe0.
Now i want to use pipe 1 to transmit from one nRF24L01+ to the star center, with ACK this time...
Hi All,
I would need to get around 11Mbps data rate. I need around 5meters range. Is it possible to use multiple antennas and do a sort of MIMO.
Thanks,
Paul
Hi,
i am disabling ppi channel so that my adc should stop working(i am taking data from 3-axis accelerometer), this process i am doing by pressing button(bsp_event_handler...
Hi, I am currently working on a project, where I need to change my timer ticks whenever I receive a number from the UART app. The code for receiving data is complete, but...
I am looking for a solution to determine the IC revision information as well as the build code for the nRF52.
For the nRF51 series exists this compatibility matrix pdf...
Hi,all~
I got a question about pwm's timer. Here is my working environment: SDK 10.0, SD8.0, IC VERSION: qfabc0.
I use timer1 as clock of pwm. APP_PWM_INSTANCE(PWM1...
Hi Everyone!!!
I am interested in nrf52832. I was going through its product specification v1.2 available over here: link text
At page no: 1, in the section: Key Features...
I have a nrf51 Dongle handy and I'm wondering if it can be used as an ANT+ to USB gateway for running simulANT+ on my PC?
If this is possible, where can I find the dongle...
Hello, I have device with nrf51822-qfab and I need to run ble_app_template (use softdevice s110). What version of SoftDevice I must to use with SDK v6.1? About problem: It...
Hello, I find these structs:
ble_gatts_attr_md_t
ble_gatts_char_md_t
show up quite often in example projects. My qeustions are:
What are these? And when will I be...
I am using esb dpl in nrf5 sdk v11. I want to put a special packet in ack payload. but I think nrf_esb.c code can not do. the reason is that when on_radio_disabled_rx() is...
Hi,
I am developing a printed circuit board for myself using a NRF52 and I am unsure how to actually burn a bootloader program to the NRF52. Additionally, once the bootloader...
Hi All,
my device wakeup from system off casued from reset RWOFF, I read the register RESETSRC and byte E is 1.
maybe there is something about the configuration of gpio...
Hello,
I was reading about that 6LowPAN is being used in the IoT SDK.
I have a few questions about this.
Can the 6LoWPAN node communicate with another 6LoWPAN node...
