Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi!
We are developing home automation light control mesh products.
We use nrf52832 DK (PCA10040), with nRF Connect SDK Toolchain v2.7.0 and nRF Connect SDK v2.6.1
We...
hi,
After upgrading mcuboot from NCS 2.6.1 to NCS 2.9.0, the upgrade file is downloaded, and the device restarts and runs normally. The mcuboot version number and active...
I have a nRF54L15-PDK kit. I also have the latest v2.9.1 SDK and toolchains installed using the VSCode plugin (also latest).
I use the plugin to create a new application...
I am new to designing with Nordic microcontrollers. I am at the point in my design where I am laying out connections to the microcontroller and setting up which pins will...
when I tried to add a device to nrf cloud, I am getting an error message 40101
My device is nrf9151dk with IMEI 359404230049133 and HWID 374155 I believe I might have registered...
I am exploring the possibility of using ncs v2.8.0 for Mesh with Coded PHY on the nRF52840dk/ nRF52840 board . I know this is not officially supported.
I started with the...
Dear,
I’m using nRF Connect SDK 2.7.0 with BLE Mesh and wondering how to adjust the TX power dynamically. When setting the TX power using a predefined option like CONFIG_BT_CTLR_TX_PWR_PLUS_8...
NCS 2.7.0
nrf52840
I'm currently porting software that was originally developed for nrf52832 on NRF5 SDK to run on Zephyr. I am currently on a deadline to delivery a prototype...
I've tried to follow the exercises from the Bluetooth Low Energy Fundamentals course. When I try to run the solution for lesson 3 exercise 2 I get the following error messagen...
Hello,
I have some previous code that ran using BT mesh. I then updated SDK's to 2.9.0 and I am now having issues provisioning devices. I am using the BT Mesh Provisioning...
Hi,
We are currently developing an application where we use a nrf52811. Currently i am working on integrating the BLE-Stack as this is the last part missing.
I am constantly...
Hello -
I am working through the DevAcademy - nRF Connect SDK Intermediate lessons. I have reached Lesson 7 Exercise 1, found here - https://academy.nordicsemi.com/courses...
Hi Team,
For my project, I am using nRF 5340 board and using the Zephyr SDK for development. I need to read and write data from/to an external QSPI EEPROM used ( MP95P08...
Smartbadge epaper custom board using nrf5340/nrf7002, with an NFC loop to allow NFC card emulation/communication. Building using NCS2.9 with sysbuild.
I want to be able...
Hi,
I just have a simple question => could you please tell me what are the ECCN numbers associated to this software:
www.nordicsemi.com/.../nRF-Connect-SDK
Thanks in...
