Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Using: NRF52840, SDK 14.2, S140
My GPIO initialization code is as follows. This is the first thing that happens in main.c.
Here are logic analyzer traces of 2 GPIOs...
Hi
We would like to adjust the pin matching of our nRF52805 design since the measured S11 coefficients in Tx mode are not very good (well above -3dB). The values for the...
Hi.
I am testing a wearable device based on nRF52832 and it does not have a reboot button.
Sometimes the device gets stuck and does not appear on Bluetooth scans. Rebooting...
Hello, I'm in Zephyr OS build v2.3.0 and NCS v1.3.0. I need to reprogram UART0 baudrate at run time to 38400. After having obtained the uart node
uart = device_get_binding...
I want to transmit UART and Bluetooth through 12bit ADC 12k sampling.
I downloaded the following example and verified the ADC-UART AND Bluetooth communication. https://github...
Hi,
I use the nRF52840 chip, which is designed as a module.
I use nRF9160 DK to burn the hex file.
1.And i can use nRF connect to read the ic of the module.
But...
Hi there, We're using SDK 16.0.0_98a98e2. Our setup is a PC running BLE Central connecting to 2 nRF 52840 running as BLE peripherals. We use the provided BLE UART example...
Dir Sir or Madam,
I defined 2 properties in sensor_server mesh example,
Precise Present Ambient Temperature (0x0075) and Present Indoor Relative Humidity (0x00A7) ,
...
Hi,
I use sd system power off to go into sleep mode. I wake up with the help of a button. However, the 1 second wake up time is too much for us. Do we have a chance to set...
I am currently trying to send indefinitely large files over BLE. To do this I have a central and peripheral application running between 2 nRF52840's (one peripheral, one central...
Hi,
NRF52832, SD S132 7.0.1, SDK16, custom device, custom SW
The: custom device not bonded.
In my firmware I can run beaconing in parallel with connectivity advertisement...
Hi sir,
I encountered a problem while building Thingy SDK using segger. Here are steps what I did,
Downloaded "thingy_sdk_v2.1.0" SDK from this https://www.nordicsemi...
Hi there,
When I operate SPI and I2C simultaneously on nRF52832, an error has occurred.
Could you please teach me how to solve an error?
I use an attached "main.c"....
