I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Using SD API v6, connectivity_4.1.2_usb_with_s140_6.1.1.hex, and pc-ble-driver Github release 4.1.2-win_x86_64. I can read and write small characteristics, e.g. 20 octets...
I want to time period 153us.
This is my calculation.
153us = 6535Hz.
PRESCALER = (32768 Hz / 6535 Hz )-1 = 4
There is
// <o> APP_TIMER_CONFIG_RTC_FREQUENCY...
Hi,
I want to use external power (battery) and USB power together.
If USB is not connected, I want to supply it with battery power, and if USB is connected, I want to...
Dear HW engineer,
I have ordered a few custom boards with nRF52820. As recommended by the datasheet, I have used 12pF load capacitors for both HF (32MHz) and LF (32kHz)...
Hello
I use nrf52832 and SDK v17.
I'm conducting various tests on Bluetooth. And I faced a lot of new problems. I erased a previously saved bond from the Android nrf connect...
Hi
After successfully testing nRF9160 SLM app. we plan to use nRF9160 with UDP and LwM2M protocol in our smart devices. We also have our private cloud server where all the...
Im new using Nordic devices , I am trying to using nrf52840DK to locate nrf52840 dongles using the direction finding method , how can I connect the dongles to the DK and build...
HI,
Is it possible to update modem firmware from 1.2.0 straight to 1.2.2? Or is it the only way to first update from 1.2.0 to 1.2.1 and then to 1.2.2?
Regards, Tero
Hello
I'm testing the firmware using the BLE. When I upload, I can see that the board is working. Also, I don't think there's a problem with running each line of debugger...
I'm trying to build the blinky zephyr sample for nRF Connect SDK and get the following failure:
Creating solution blinky.emProject
/usr/local/bin/cmake -GNinja -DBOARD...
How can I, from the pc-ble-driver API, send an insufficient authentication request without configuring a characteristic to be secured?
I am testing out new standards. One...
Hello, Nordic community,
I want to implement OTA using Thread with nRF Connect SDK.
Is there any sample code or reference this can be done with Thread?
Thanks,
...
Is there a limit to the number of handlers that can be registered using NRF_PWR_MGMT_HANDLER_REGISTER? I can't seem to get any more than 3 to be called, changing NRF_PWR_MGMT_CONFIG_HANDLER_PRIORITY_COUNT...
Hi--I'm part of a research group that will be using the Thingy 52 to record environmental variables, and we will need to transfer information to a cloud server using a satellite...
