I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
Hello,
I am working on developing a program where the nRF52840 dongle is a central device and recognized as an HID keyboard to the computer.
I played around with the peripheral...
I am trying to get a periodic interrupt every 100 uS using TIMER4. My timers_init() code sets up the TIMER4 registers as follows:
My interrupt service routine for now...
Hello
I would like to evaluate the module in a place without Cat-M \ NBIoT support
is it possible (for evaluation purposes) to send the data by other means (for example...
Hi,
New to Nordic, new to SEGGER, and new to ARM, so forgive me if I'm just missing something...
I've been asked to write new code for some boards that have the nRF51822...
I am using the SPIM example in the nRF52840 SDK. It uses SPI_INSTANCE 3. I am doing a simple SPI Write of 2 bytes.
I get SS, SCK, working properly. MOSI is transitioning...
I want to take drive code from thingy sdk and apply it to nrf5 sdk uart project, but I don't know how. Please explain in detail because i'm university student ... thank you...
Hi Team Nordic,
I am trying to save my flash data after the DFU process but it keeps on erasing it. I saw a thread in which it was explained to increase the CODE_PAGE_SIZE...
Hello,
I have a problem with app_timer.
My program need to use BLE UART for about 15 second then switch for just RADIO after.
To do so, I enable the ble stack as...
hello support team
nRF52 DK , Mesh 2.01
I am trying Experimental BLE RELAY example.
1. In first trial I am using 1 RELAY DK all works well.
2.In second Trial I am...
Hi everyone, I have a custom board using nRF52832 chip.
I want to turn ON and OFF a LED, which is directly connected to a GPIO pin.
Using this configuration I expect...
Hi,
I want to use the math.h for my nRF9160 project, but when I include it, it doesn't find it. I am a beginner and I wanted to ask how do I include libarys proparly in...
Hi,
I have two nRF54840 DK and I am testing ble_app_att_mtu_throughput example with the boards. I am using nRF5_SDK_15.3.0_59ac345 SDK.
The number on the chip is "N52840...
Hello!
Im getting a hardfault when trying to send 10 bytes data via NUS. I receive the data, but the app crashes:
0> <error> hardfault: HARD FAULT at 0x00000000 0...
Hi everybody. I know that it is complete standart question, which has many asks and solutions here. I'm quite new to bootloader management stuff. So asking about some targeting...
