When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
Hi!
I searched the devzone and there is quite few topics about how the relay is enabled / disabled in the FW... according to https://www.youtube.com/watch?v=r9CvtbCmYQY...
Hi,
I'm unable to hit my break points while using the J-link Lite debugger.
Mostly, after I've attached the debugger and reset, it goes to the correct location
FUNC_NORETURN...
Hi,
I am using the nrf51422 controller and other controller which contains Bluetooth .The nrf51422 Bluetooth is central and other controller Bluetooth is peripheral.I am...
Hi to all,
I am using nRF52832 DK with SDK 15.0 version. My two nRF52 DK damaged while debugging I am a little bit confused why this happening.
When I debugging I used...
Hi,
I need a way to dynamically disable watchdog when I do MMD debugging. I found the old trick, check bit 0 on CoreDebug->DHCSR, does not work any more in MMD. Is that...
I suspect a possible race condition happening during NUS service discoveries. I have two peripherals that are advertising and have DIS, Battery and the NUS service enabled...
Hello,
I have configured max30101 with nrf51 and I want to read the fifo of max30101. The fifo can contain 32 samples and the size of each sample could vary from 3-9 bytes...
I followed the suggestions in https://devzone.nordicsemi.com/f/nordic-q-a/51642/can-t-build-nrf-connect-asset-tracker
But, still having the same issue.
Using tag v1.0...
On one of our products, we are experiencing approximately 4% failures during production. I traced the problem to be caused by function sd_softdevice_enable not returning....
Hi Devs,
based on this example
https://github.com/NordicPlayground/nRF52-Bluetooth-Course
i was able to run it, and the value field appear below the Unknown Characteristics...
Hello Everyone, I newbie to BLE world and new to programming. Currently I am following this github repo: https://github.com/sandeepmistry/arduino-BLEPeripheral . I am using...
Dear team, Device - nRF52832 SDK - nRF_SDK_15.0.0 Softdevice - s132_nrf_6.0.0 IDE - Segger embedded studio
My application needs to toggle one gpio pin using app timer in...
I'm developing for the nrf9160 and would like to clone the sample projects at https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160
branch nrf9160_samples...
Hello,
I'm using SDK15.3 (Generic_Stack_S332_06.01.01).
IROM1 Add :0x30000
IRAM1 Add : 0x20003600
Central Firmware support already in SDK14.3 just I move this part...
