i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
I am running the light_switch example and it works fine works fine , I am using the nrf_application to configure the nodes.
I am using latest mesh sdk and 15.3 nrf sdk....
Hi guys
I had to integrate a CLI module into a project I'm working on, that is running FreeRTOS
after quite a lot of work, I managed to get this working, but seeing...
HI,
I am using nrf52832 dk. I have a sensor that gives a negative voltage. I want to measure the value using saadc.
and can I use differential mode saadc for negative...
Hello All,
I am working on the N51822 custom board.
Using segger IDE, SDK 12.3
Previously i have worked on the sdk 14.3 on the n52810 board. It is working properly...
Hello
I am using pin 1.15 of nrf52840 dongle with transistor with enable pin of another chip. The other chip is a wifi chip which I only want to switch on whenever I have...
Hi All
I am using nRF9160 DK version 0.8.5, and I have gone through this link, downloaded and Installed all the steps, given there. All seems to be running good.
But some...
Hi I am using the custom_bluetooth_service tutorial from https://github.com/bjornspockeli/custom_ble_service_example with SDK v15 and nrf52840 DK.
I am now trying to use...
Win10 + Segger embedded studio
I can get the pca10059 blinky example to work. ( C:\nRF5_SDK_15.3.0_59ac345\examples\peripheral\blinky )
I use the NRF connect Programmer...
We are trying to receive high speed data using UART. Currently our source is set to transmit an 8 byte packet once every second.
I have initialised the serial port in IRQ...
Is there a public bug-tracker available (even better: publicly hosted repository)? I'm currently trying to wrap the SDK in way suitable for our internal processes (CMake,...
Hi,
i'm using "cycling speed and cadence" on DK to make a test run. However, my bicycle-watch(base on ANT) doesn't receive any "ANT signal".
Searching in the devzone,...
On the picture channel 2 connected to reset button on PDK.
UART channel drops to GND 4ms after button pressed.
How to prevent this?
Tried this: https://devzone.nordicsemi...
Hello,
at 3.3V the current consumption of my development kit is about 21.5 µA.
Due to the law of energy conservation, I would expect the current at 1.8V to be a little...
Hi,
i'm not getting any signal with a fresh DK and the latest modem driver.
entering AT+COPS=? will make it unresponsive forever. (nordic LTE Link monitor times...
