Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I'm using the pstorage driver on the nRF51 to maintain several NVM variables. The NVM functions correctly and maintains state between power cycles. However, when I reflash...
Hello to all Nordic jedi masters!
I am using the nRF52832 along with SDK v11.0
I want to have the SAADC generate events only when the converted value is above a certain...
Hi all,
I am using a nRF52-DK board to receive data from the USB port using Serial, and transmitting it using ESB to a second board. If I use either Serial or ESB individually...
The latest rev of the product spec (1.1 when this was posted) includes a table on page 77 that indicates that the System OFF draw depends on a wakeup source (e.g. GPIO, NFC...
while i open ble sniffer , it sucessfully recognizes the nrf51822 ble nano but when i press w to open the wireshark, it shows no packets and in the interface list it shows...
Example ble_app_uart compiled in Keil 5 O.K but the resultant HEX file in the build folder is only 34K whereas the hex file in the hex folder is 335k. I followed the tutorial...
Hi Nordic team,
Very impressive demo posted on the blog zone this week! I'm trying to understand the details and sorry if I ask something what would be visible in the source...
After upgrading to iOS 10, I have been unable to successfully interact with my device using the NUS. I used to use the NUS to communication with the device and retrieve stats...
Hi, my setup is:
nRF52 DK PCA1040 v1.0.1;
Adafruit MAX9814 electret microphone amplifier;
My project concerns about:
Sampling audio from the board with...
Hi,
I fix bug in original code and managed for nRF51822_xxAB. It is bootloader for application based on SDK7.This bootloader is buttonless and application start after 60s...
Hi all,
When using GCC and Eclipse with SDK 13.0.0 to program an nRF52832 with the Serial and ESB libraries, are there any limitations as to where you can put event handlers...
if i set the attr_md.vloc = BLE_GATTS_VLOC_STACK;
how to set the attr_char_value.p_value?
attr_md.read_perm = p_rrthermomter_init->rrthermomter_attr_md.read_perm;
attr_md...
I am working on a BLE project, n i have bought nrf51822 BLE nano chip. but honestly speaking i got stuck in installation itself. i have tried the blinky, HRM examples given...
I am wanting to use pstorage for storing a few persistent variables. I am working from the multilink central example, which already is using pstorage for, I assume, saving...
