Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
I know how to OTA a ble device, but how do this on a ble master?
Is there any nrf tool can OTA a ble master ?
dev environment:
SoftDevices:S130 v2.0.1
sdk: nRF5_SDK_12...
Hi,
we are using a ISP130301 module from Insight SIP (containing a nrf51822CEAA ) with a low power acceleration sensor ADXL362 , connected via SPI. SoftDevice is s130_nrf51_2...
Hi,
SDK: nRF5_SDK_12.2.0_f012efa
No softdevice
Example: nRF5_SDK_12.2.0_f012efa\examples\peripheral\radio\transmitter\pca10040\blank
and receiver.
I have running...
Hello,
I am using nrf51 and firmware is ble_app_gls. I have modified my code to work for dfu as well.
I am getting error as follows
.\_build\nrf51422_xxac.axf: Error...
I try to integrate the CoAP Server and TFTP DFU example code, and it works well.
[ENV]
IoT SDK v0.9.0
nRF52832 DK
According to the specification, the MTU...
Hi, dear support team,
I program the softdevice(S110,v7.1.0) to the nRF51822 devices(our product) by nRFgo Studio v1.21.1.3.
The nRFgo Studio shows a error message as...
Good afternoon.
I have 2 boards NRF51:
One as beacon (SDK 9), use example code "nRF51_SDK_9.0.0\examples\ble_peripheral\ble_app_beacon".
The other as...
Hi,
I have a problem using Secure DFU Bootloader available in SDK 12.1 on nRF51822_xxAA SoC.
Initilaly i was using nRF51 DK board and Secure Bootloader example in SDK...
Hello,
In our application, we do not use the antenna at Pin30.
However, in Nordic's Reference design in Github, even the simplest design (nRF52832_qfaa_dcdc) has an...
Hello,
Can I interact with the internal device of the nRF52 DK (PCA10040) while an other nRF52 connected through the P20 (or P19) connector?
The JLink tool has a "device...
I implemented an application to advertise indefinitely with APP_ADV_TIMEOUT_IN_SECONDS set to 0 and it works just fine. Now I want to
have a time out and set APP_ADV_TIMEOUT_IN_SECONDS...
Reading the nRF51 RM. On page 82 there is this:
But it doesn't make sense to me to talk about the LSByte of the PAYLOAD field, as it's just arbitrary data, and the Radio...
Has anyone had issues with connecting to the nrf52 DK with linux hcitool? I am able to see the device's MAC address and name (using HRM example design) with hcitool lescan...
I have everything working nicely with gcc, my own Makefiles, and the Nordic SDK12.2. I'd like to move to CMake to better automate my process (in particular, compiling one...
