Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi there:
I found a strange phonomenon about consumption betweeen advtisement and gpio17 of 51822.
When I start ble adv while setting gpio17 to input disconnected mode with...
Hi, possibly a bit of a stupid question but here we go:
I'm developing a prototype system, which includes my own design of sensor modules that transmit their data via nrf24l01...
Hi, Nordic
I know when I program one BLE app, softdevice should be needed.
If I program esb/gazell app, softdevice is not needed.
I want to know, when I program one...
Hi, Nordic
I want to add BLE DFU service in my own app, so that the nRF52 can operate BLE DFU.
I only modify 2 places:
static void services_init(void) --> init ble_dfu_init_t...
Hi，Nordic
I am working for BLE_DFU, on SDK 12.1 and SoftDevice s132.
I checked, I should add below code in ble_dfu.c
char_md.char_props.write = 1;
Then I added...
Hi, Nordic
I check SDK13.0 bootloader_secure sample, it do not work
nrfjprog download bootloader_secure
use nRF Connect app in Android mobile phone to...
Howdy!
I have to admit that after about 2 weekes of fight i finally made some progress with NRF51. Afterall i can upload my own program to chip so it changes leds on NRF51...
I get an error when trying to pair to a peripheral in nRF connect v1.0 on Linux.
I have two nRF-DK v1.1.0 (pca10040), one is the adapter that is connected to nRF Connect...
After flashing softdevice, the ble_advertising_evt_handler_t doesn't get called, only after flashing the program for the 4th time.
/**@brief Function for initializing advertising...
When I connect the nordic ID stix to my android tablet using the micro-USB to USB cable, the nordic ID stix doesn't appear green light on it. Is it need to install any driver...
I would like to dynamically change bluetooth LE advertising interval. I am using nRF51 and nRF52, with SDK's 8 and 12. Is that possible and how to do it?
Our application...
Good day everyone,
I would like to utilise the nRF52832 BLE chip in an application that requires radio communication between a master and slave. The slave needs to be powered...
Hi everyone,
I am using LPCOMP in rFF58122.
When coosing the reference voltage, I have to fill the structure nrf_drv_lpcomp_config_t with the hal nrf_lpcomp_config_t that...
Hello, I try to add TWI function in my project (uVision5) so I add this modules with 'Manage Run-time Environement':
nrf_drv_twi
nrf_twi
app_twi
and I get...
hi
I have a problem in integrating a 1.8V GSM modem with nRF52832 through UART. nRF52832 supplied with 3.3V and there is a voltage divider that covert 3.3V to 1.8V in the...
