Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hello, I am working on low power modes and I got trouble finding the code to switch from NRF_POWER_MODE_CONSTLAT and NRF_POWER_MODE_LOWPWR. Can anyone please guide me to better...
Bonding causes power consumption to rise.
I have a central and peripheral device communicating using the nus-service. The peripheral device is running FreeRTOS with tickless...
Hi,
I'm trying to test the DFU over HCI included in the SDK examples but I can't make it work. This is all the information of the environment I'm using:
SDK: 10.0...
Condition: nRF52, SDK11,s132, SDS v2.0.
Using the sd_ble_gatts_hvx() in timer1 interrupt service(timer1 interrupt priority is set to level 3) will result in hardfault. While...
I am using SDK_11 s130. I am looking at app_error_fault_handler() in app_error_weak.c
Inside app_error_fault_handler(), there is this line of code;
UNUSED_VARIABLE(bsp_indication_set...
Hi,
I am using keil uvision 5.17, SD 130, nRF 51822, dualbank bootloader.
I have programmed own application and merged bootloader, application, soft device.
I...
I am using ble_app_gls on SDK_11 s130 on nRF51-dk.
This is a follow-up question to the question below.
devzone.nordicsemi.com/.../
After enabling debugging, I discovered...
Hi,
I'm using the example projects "ble_peripheral/ble_app_uart" "ble_central/ble_app_uart_c" in SDK10.0.0 to test data throughput.
I'm sending 20bytes of payload. But...
Hi,
I am using nrfjprog package installed in folder /opt/Nrfjprog. I am getting the fallowing error.
nrfjprog --eraseall
ERROR: JLinkARM.dll load failed. Try again...
Hi,
I've migrate from 3V to 1.8v power supply.
before the migration, using 3V power supply, DEC2 connected to 47nF directly to GND.
after the migration, using1.8V power...
in android program i disconnect from my gat with this code
while(isconnected){
mbluetoothGatt.disconnect();
Log.d(TAG, "Disconnecttodevice: ");
}
mbluetoothGatt...
Hello, I load UART over BLE example on nrf51DK (51422) DK board and measure for 13 seconds from power on.
Here is the result graph and the average current is about 175uAh...
Hello Nordic! In my FW, I need to know when a specific packet has been actually sent (because of SD packet buffering). I am able to receive the BLE_EVT_TX_COMPLETE event,...
Hello I'm using SDK nRF5_SDK_11.0.0_89a8197.zip and I find out that most freeRTOS file version is: "FreeRTOS V8.2.1" but "external\freertos\config\FreeRTOSConfig.h" is in...
