Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, in evothing and mbed all the UUID are 128bits long
however, in EK, the code use 16bit UUID
ex. nus.c the uuid is 0x0001 0x0002 0x0003
any one knows how to provide...
Hi,
I have just received my smart beacon kit (nRF51822 based), I have wired up my JLink programmer according to devzone.nordicsemi.com/.../
However I am having trouble...
Hi!
I'm building a mesh using beacons. Everything works good untill now, except beacons sometime stop advertising on its own. Beacon still works because he still connects...
Hi. We are going to mass production now and the lab that will certify our product says we need to have a special mode in the firmware that would do : modulated middle channel...
I want to make a custom board using nRF51822. Currently I am using nRF go studio starter kit and pca10005 board. I am using segger jtag programmer for loading code to the...
Hello,
I have a custom program based on the uart example. I can write to the device, but sending to the master fails.
I call the SendString code, but p_nus->is_notification_enabled...
Problem
I got some problem in change device name.
I found that the function of ble.gap.setDeviceName(deviceName) is useless.
So I've searching for another function...
Hi,
Does anyone know if there are plans to support RTX in the nRF52 SDK? It is included in the nRF51 SDK under external/rtx , and there is an example in examples/peripheral...
Hi,
I have purchased the nRF8001 DK and it came with no documentations. I downloaded the nRF8001 DK User Guide V1.1.
In this documentation, under section 1.3 there is...
I have setup environment on QT creator and i am using JLink GDB server debugger.The nordic chip is nrf51822 QF AA H0 and SDK is nrf51822 s110 version 8.1.0 .I read some posts...
I donwloaded the iOS nrf toolbox. I found that the app converts the glucose measurement to KG/L and not to mmol/l? The reading on the glucometer is in mg/dl so when I multiplied...
Hi,
I am trying to get my mesh running on the nRF52 Preview DK but calling
SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, NULL);
will break my program...
I am using nrf51422 and ble app uart as my example code and trying to connect to my ios app nrf toolbox by enabling a static key for the pairing process. i have read all the...
After installing the Master Control Panel 3.10.0.14 (x64) on Windows 7 Professional, uninstalling JLink V5.02a (which MCP really does not like) so it uses V4.98c, and realizing...
