Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Dear Nordic Community, I want to build samples/basic/blinkly on nordic nrf52840_dongle inside my Zephyr workspace. I use Zephyr 4.2.0, but on Zephyr 4.3.0 I have similar problems...
Hello, I am looking at pages 871 and 872 of the datasheet for the QFN48 package, but I’m not sure I understand correctly. Could you please tell me which GPIO P0 pins can be...
I’m using an nRF54L15 evaluation board obtained from a distributor and currently testing transmission and reception of large data chunks. Everything was working fine until...
I have an external device. After connecting it to the central device, I found that the Bluetooth service of my external device couldn't be enabled properly. When I checked...
Hi, I have the radio_test example running correctly on a nrf52840 dev board. I am able to use the Nordic Serial Terminal (v1.6.0) to send commands and read responses.
...
I am developing a custom board using nrf54l10 chip. So far, I have been able to use a code to comunicate through spi and uart for me to use printk function.
Now I was trying...
The docs( docs.nordicsemi.com/.../dect.html say that th nRF9151 modem can't do GPS/LTE and DECT NR+ at the same. Could the modem switch between the two operation modes while...
Hello team,
I am using SPI00 of NRF54L15 to communicate with w25q32fv (spi Flash). Below is the configuration I set in .overlay file
And below is the code I am using...
Hi,
I have a question about the the fields " tod_toa_reflector" and "toa_tod_initiator" in struct bt_hci_le_cs_step_data_mode_1.
I understand that these values represent...
The e-mail contains news of a new use of the nRF9151 module but uses the word "proves" and as an English language Cambridge qualified teacher I must mention that the word...
Issue description
I am using SAADC in single-ended mode with 3 channels (0/1/2). Measurements are performed by enabling SAADC, running offset calibration, configuring the...
Hello,
I have an application running on legacy NRF SDK and using the nRF5 bootloader, which has below flash sectors, 0x00000 - 0x026000 - Soft-device section 0x26000 - 0x0D9000...
Our custom product, based on the nRF52832, is undergoing certification. The testing laboratory requires that only one BLE advertising channel be active at a time—first channel...
Hi there,
We have a mass produced product with a modified secure bootloader (from SDK17). This BL has BLE and USB and we bolted on an SPI flash transport for OTA updates...
