I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
HI
This is regarding to create a project which supports below peripheral
1. Uart : To interact with Windows application - Working Configured Successfully
2. I2C: for...
The instructions at https://github.com/NordicSemiconductor/pc-ble-driver do not allow building the driver or the examples on a Windows system. Following the instructions takes...
Hi, I developed a BLE and Zigbee custom product, starting from nRF5 SDK for Thread and Zigbee v3.2.0. On BLE side, it connects with Mobile or Tablet using Pairing with bonding...
Hi,
1. Does nRF52840 CKAA WLCSP support QSPI 32MHz?
2. What should qSPI 32MHz measured CLK waveform look like?
3. Is there a 32M QSPI CLK sample diagram actually measured...
I finally had success in getting a SPIM master running with a single SPI slave (Honeywell sensor running CS 4 on the Arduino R3 header) on my nRF9160DK. But now I need to...
Dear all:
I am developing a ble scanner using RADIO Peripheral.
I have 2 questions to ask
1.When is the END event triggered?, How does the hareware know the packet is...
I received the hardfault in the following image.
The function at the address 0x00028C44 is:
The hardfault did not occur again after resetting. I'm not sure why this...
Hello,
We have a PIC32 controlling the NRF24L01 with some sucess so far.
But sometimes we get the chip in a state that we can't get off.
We still cannot pinpoint the...
Hi Team,
I am developing an application that nordic chips receive data from msp430 chips by the SPI, and send them out.
Nordic can receive the data from the msp430, but...
Hello everyone,
I tried to add the long press event into my bsp_event_handler without success. I get the normal button press event, but the long button press event is not...
Dear Nordic FAE:
Where can I find the nrf52840-CIAA REACH report?
i can not find it by
focenter.nordicsemi.com/index.jsp?topic=%252Fcom.nordic.infocenter.sdk5.v12.2...
Issue:
While trying to initialize and check the viability of an I2C interface using TWIM, my NRF_TWIM_TASK_STOP never triggers NRF_TWIM_EVENT_STOPPED.
Code:
This causes...
Hi,
I have installed the v1.8.0 nrf connect sdk and created a new application using the nrf connect vscode extension based on the ble/throughput example. Created a build...
Dear Nordic Engineer
I would like to know the version of openthread in NCS 1.8.0? And what is the otbr posix version corresponding to rcp firmware? It is reflected in the...
