I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
Hi
The 'ble_app_multiperipheral_pca10056_s140' example for the nRF52840 has an 'LED' characteristic under which there is a "Nordic LED Button Service"
The value...
Hi,
I've defined:
#define NRF_SDH_BLE_GATT_MAX_MTU_SIZE 120 (in sdk_config.h)
I get "Insufficient RAM allocated for the SoftDevice" in nrf_sdh_ble_enable
nrf_sdh_ble_enable...
Hi everyone, I'm looking to buy nRF52840 SoC for my thesis but I'm surprised that none are yet available from Farnell, Mouser or Digikey ... I found few chips on Symmetry...
Dear Engineer,
We are working on 52840 usb dfu,program softdevice s140_6.0,
and usb secure bootloader,
evaluate board is pca10056,v0.9.0
Led1,led3 turn on once load...
I am very new to ARM controllers. All of my experience is with Atmel family, which I've been using for years.
I just got the nRF52 Development board and have loaded several...
Why do the version numbers have to be as follows for a merged hex file to be able to exit the dfu mode when flashed externally as a combined hex file (SD +BL + BL settings...
With the BT 5 extensions, is it now possible for BLE Peripherals to communicate with each other without a Central ?
In the envisaged application, one node would be the central...
Hello,
my problem is reproducable with this Setup:
nRF5-DK with ble_blinky_example (central)
nRF5-DK with ble_blinky_example (peripheral)
Press Button1 immediately...
Hi,
We are using nrf8240 SDK15 and need to convert soft image which is in hex format to binary format. Tried using 'arm-none-eabi-objcopy' for this. It converts 424kbytes...
Hello Nordic team,
I am developing a proprietary radio protocol and i am using aes ccm peripheral for encryption (i am a begginer). The packets seem to be correctly encrypted...
Hi,
Can you guide as to how to set up an proxy node that participates in mesh activities as well as connects with an non mesh device (viz Mobile) from time to get data from...
I’ve been working in a small group to use the advertising extensions in BT5 to send 12 hours of temperature measurements in one advertising packets. We’ve been developing...
Hello,
I am working on ble/audio application on nrf52832. I would like to know how to compile OPUS codec (used in smart remote) so I can use it on arm cortex. For now I...
Hello,
Would it be possible to use nrf_pwr_mgmt_run() to implement a polled wait function? The nrf_delay functions execute a busy wait which is only feasible for very short...
Dear sir,
I am trying to interface MAX 30205 with NRF52832. On thec oscilloscope I am getting the signals but still I am not getting the temperature data. Herewith I am...
