Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
The note on the IoT softdevice says:
"This SoftDevice is a technology prototype only. Therefore, it should never be used in production."
Will there ever be a production...
Hi
I know perfectly it is not possible to debug while the softdevice is enable and the Bluetooth is working. When I try to set up a breakpoint under these conditions, the...
hello there i want to communicate nrf51 and nrf52 using i2c protocol. [https://devzone.nordicsemi.com/question/75218/i2c-in-nrf51/?answer=75221#post-id-75221]
from this...
Hi ,
I am working on the heart_rate_collector example code of nrf51-ble-driver_linux_0.5.0.
The program detail of nrf51 as below:
-- sorftdevice : s130_nrf51_1.0...
Good morning,
I have designed a prototype based on nRF51822 device. Now, I want to program it with a demo software and I have the Ulink-me tool instead of Segger. From Keil...
Hey ,
I'm trying to implement a device that waits for the clicks from the user and sends it over ble as notifications.
i have written the header files for sensor . and from...
im trying to get my nrf51822 connecting only to my phone, I set the phone mac address on white list, but I cant connect to my phone (android) wiht nrf master control.
How...
When my program hits an error returned by an NRF API call, I get a hex number corresponding to that error from the app_error.c:
case NRF_FAULT_ID_SDK_ERROR:
m_error_data...
We've got devices that are out in the field which were built on SDK6.1 w/ 110 SoftDevice 7.1.0 on an nRF51822.
Went with the dual-banked solution as that was what was available...
We are developing a blood glucose meter based on the nRF51.
To comply with Bluetooth Continua, do we just implement the Glucose Profile and Service (GLP and GLS)?
Do you...
Hi everyone,
I pass few days to try to fix my issue whiteout success.
I'm working on UART example provide by SDK 10 and tried to set up a communication from my computer...
Because of the power-saving support, I want to disable the UART before Call the sd_app_evt_wait().
I referred to two following sites to know the procedure of the case....
I'm working with a nrf51422/s110 dev kit on which I downloaded the Heart rate Monitoring sample project. On my PC, using a s130 dongle, I connect the device and wrote some...
Hello,
I would like to know about the possibility of programming the nrf51822 with a Keil ULINK-ME Debug Adapter (or, if necessary, Keil ULINKpro) instead of the recommended...
Our product has a legacy interface and for security reasons I want to allow users to disable or enable the BLE via this legacy interface.
My approach to this was to disable...
