Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
Hi, I am trying to generate PWM pulse based on sample application in GitHub. However instead of using different modes and multiple channels, I tried to simplify it to just...
Probably a silly question, but I am new to Nordic Semiconductor and can't figure this out. I am trying to make a new project based on the Template example for nrf51422_xxac_s100...
I am writing my own function to setup a notification characteristic, but it failed,
Could anyone help me check it ?
static uint8_t d[2] = {0};
static ble_gatts_char_handles_t...
I have been experimenting with mbed ble programming and have had some success with the examples and my own programs. Everything works fine on the nRF51 dongle and DK.
I...
I'm trying to enable the active signal for an nRF8001 on Adafruit's breakout board. Is there a way to do this without using the nRFgo software? I use a Mac so setting up nRFgo...
Hello.
I use BLE Shield V.2.1 of RedBearLab.com for Arduino.
The shield equipped nRF8001.
After about 62ms from reset nRF8001 by putting Low signal in Arduino pin 4...
Iam using NRF8001 in my project & i don't know how to enable them & connect them through Android app basically iam using in tracking chip so any one have a idea that how to...
I am using an Arduino and NRF8001 break out board from Adafruit. I am using the UART profile (adafruit sample code) to send data between mobile phone and Arduino. However...
Hi,
I am trying to setup the nrf8001 by sending the setup commands from my microcontroller. After I send the complete setup packet (21 commands) I receive, as expected...
I'm working on integrating nrf8001 with STM32, currently trying to write my own stack.
Upon reset, I read the DeviceStartedEvent, 0x81 and it shows "0x02 0x00 0x02", which...
After a fresh install of Keil (along with Legacy patches) and the SDK, I get the following messages when I try to open the ble_app_template_s110 project:
The project...
Hi All,
I use iot_ipv6_udp_client example on nRF51 DK.
I modified it and send data in one direction only (not receiving back).
Testing has shown that the maximum packet...
Hello,
I use S130 with NUS style connections as central and device at same time. It works nice and performance is good but when i run scan, performance become very poor...
Hi,
I'm using S130 with SDK 9.0.0 and as central, I'd like to read values for more than one characteristic on a peripheral. I do so in BLE_GATTC_EVT_CHAR_DISC_RSP by firing...
