I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
I have a nRF52840-DK that I know that it has a JLink on board, but the RAK4631 don´t have JLink, then I am following the RAKWireless bootloader update( Bootloader update ...
Hi everyone,
I'm currently developing an application supposed to read through SPI from an extrernal SRAM, i'm using nrfx_spim libraries.
Compilation is flawless but when...
Settings document explain .h_set handle will be called when the value is loaded from persisted storage with settings_load().And I want to know how it work.
I put a breakpoint...
The Bluetooth connection is disconnected, but no disconnect message is printed, and no more ads can be searched, the main thread is running fine, and the Bluetooth function...
I'm trying to just do a pristine build using the Ezurio Pinnacle 100 DVK When I originally created this project from a dev board, the resource "atmel,sam0-pinctrl.yaml" and...
Hello,
We are using the nrf52832 in SES with the softdevice s112 (v7.2.0) and sdk17.1.0 in a custom board for a BLE application (that includes OTA DFU and a custom service...
Hİ,
I can connect to LTE. but somewhere which I think it might not be the signal, it can not connect and restart (reset). not return any error. if I change my location ...
Hi there,
I have purchased a Fanstel BU840XE device ( BU840XE, The longest range, Remote USB Dongle for BLE 5, Thread, Zigbee — Fanstel ) theres the link. The device has...
Hi,
1. How can the read slave interval be reduced to less than 2ms: twi_master_with_twis_slave
2. Test environment:
DK: pca10056
SDK:nRF5_SDK_17.1.0_ddde560\examples...
Hello,
I am aware that there is going to be an update to the BLE stack and you are soon releasing 2.8.0. For NCS 2.6.0 we were using 239354 for the host subsystem and...
Hi,
I use Nordic nRF52840 BLE Sniffer Dongle and this works as expected in Wireshark up to version 4.2.7. Hówever, when I upgrade Wireshark from 4.2.7 to 4.4.0, the Dongle...
In Software Maturity Levels under Trusted Firmware-M , it is stated that only the minimal build is supported, while the full build is still considered experimental.
In Running...
We have tried the following changes, but couldn't get expecting results.
Sometimes unable to pair two devices / Sometimes fails to link with one device
Could you answer...
Hi
We are using the nRF51822 with the SoftDevice S130 V2.0.1.
The nRF51 communicates with another controller via UART with a special handshake-mechanism directly on the...
