Dear Nordic,
it's about USB implementation. We need to add interface string descriptor for ineterface name. Using USBD_STRING_DESCR_DEFINE(primary) I've added that to string...
Hello, I have NRF D 24LU1P 1201FD and NRF F 24LU1P 2136IW. The first one executes all commands, while the second one does not work for writing and erasing. I tried to erase...
Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Upon initial connection with iOS device, returned connection values at BLE_GAP_EVT_CONN_PARAM_UPDATE are:
ble_event: got BLE_GAP_EVT_CONNECTED. role: 1, conn_handle: 1,...
Hello,
I using the Segger with the last SDK. I modified the ble_app_uart example, I added the softdevice to the addition files. When I run the debugger everything seems...
Hey guys, Recently i decided to get the ICM-20948 DK and exploring it. I read all the info on their site and all their guides but the only briefly get over the topic, so i...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I was going to “Batter Service”. Battery level...
Hello, I am using the PCA10056 to program a nrf52811 chip on a custom board with SDK 15.3.0. I'm using the example ble_app_blinky_pca10056_s140 I am following the steps in...
I am working on transferring BMI160 sample given in zephyr samples (\ncs\zephyr\samples\sensor\bmi160) to nrf sample (\ncs\nrf\samples\nrf9160\bmi160).
Below is the changed...
I'm having a problem with the nRF52 SAADC. It's configured for
One shot operation on Channel 0 using pin Ain4.
Gain of 1/6
Tacq set to 40us
8 bit resolution...
HI,
I want to configure HT1632 LED driver using SPI communication protocol
for that i should send commands LSB to MSB
immediately data should go MSB to LSB
My question...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’ and “nRF Connect” app.
I am trying to understand...
Hi all
SDK 11.0.0 S132 version 2.0.1 nrf52832
I want to turn on the PWM and turn off the PWM after 1 minute. The device will do BLE advertising When the device wakeup...
Hi,
I have read a lot of posts about using the internal LDO/DCDC converters or using an external switch mode regulator, but haven't seen any answers I could use.
I have...
I am looking for guidance on how to fragment data in Extended advertisement on the nRF52840. I am using the "ble_app_rscs" example to advertise in non-scannable non-connectable...
Hi ,
I need to update the NRF52832 with another different module.
I can update without problem by using the nrf connect app.
I would like to use another device without...
Hi,
I am trying to get event messages on the terminal from a Generic On Off (GOO) Client node. I have the provisioned the mesh using the pyAci through another board running...
Hi,
I am using nRF52840 Preview DK, with SDK V15.3.0 and Softdevice API V6.1.1
First, I modified the 'ble blinky peripheral example' to have more characteristics tying...
