Dear Nordic,
it's about USB implementation. We need to add interface string descriptor for ineterface name. Using USBD_STRING_DESCR_DEFINE(primary) I've added that to string...
Hello, I have NRF D 24LU1P 1201FD and NRF F 24LU1P 2136IW. The first one executes all commands, while the second one does not work for writing and erasing. I tried to erase...
Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Hi,
I am studying the GPIOTE example from SDK 14. I did some modification adding other led and doing the leds blinking in differents times (LED1 blink each 1 sec and LED2...
Hi,
The nRF52832 does not support Long Range and i was wondering if the use of "RADIO_MODE_NRF_250KBIT" would increase the range. My application is a mesh network.
Do...
Hello Everyone,
I am using nrf51822 with S130.
Currently I am using arduino following this repo to program nrf51822 and its working fine. However, I want to shift to keil...
Hi there
For test purposes, I first implemented a simple serial reading & parsing function in polling mode of a gps device (sending @ 1 Hz).
Everything works fine when...
Hello,
i am evaluating the nRF52840 on the nRF52840-Preview-DK. I have connected an ADC to the devkit via SPI and my code reads data from the ADC via GPIOTE, PPI and SPIM...
We've got two SPI slaves that we need to talk to with the 52840 (PCA10056 dev kit for now) using SPI Manager. In the initialization of these devices, I'd like to use nrf_spi_mngr_perform...
when I use flash to storage my data,I call the fds_record_write(&record_desc, &record) ,and it return success,but my machine run err, my ble broadcast is missed.I used the...
I'm trying to understand what is meant in section 5 of the BLE on Android primer: "The peripheral device should disconnect itself when it gets disconnected by the client....
Hellou, I am developing application which need data array store to flash manager. I used for some function for storing data (nrf_fstorage_init(), nrf_fstorage_erase(), nrf_fstorage_write...
Hi!
I'm trying to merge the flash_fds example with the ble_app_uart, and the twi example. My intention is to read a value from TWI, store it in flash and then send the...
Hello,
I would like to know how can I configure the parameter NRF_SDH_BLE_GAP_EVENT_LENGTH for a determined NRF_SDH_BLE_GATT_MAX_MTU_SIZE when enabling data extension. ...
hi team,
i was using nrf52840 with sd 5.0 and developed a custom application using ble_app_proximity in 14.1. my use case is my device should hand shake only with my mobile...
In the NRF_SDK_15, only 3 drivers (clock, power, rng) use the return value NRFX_ERROR_ALREADY_INITIALIZED. Why are the others drivers initialization return NRFX_ERROR_INVALID_STATE...
Hello all,
Weve figured out our hardware issues (pin arraignment) and are successfully programming via JLink.
Our goal is to replicate the bootloader/softdevice/firmware...
