Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
Hi,
I am trying to perform DFU over mesh network. I am following the steps as given in this .
I could achieve the steps from 1-6. But while running the command for Transferring...
Hi,
When running FreeRTOS I'm not able to use the NRF logger module once the task scheduler has started.
I have a low priority task that flushes the logs but whenever...
Context: nrf52840DK, s140, SDK 17.0.2
Hi,
I need to oversample a few ADC pins with burst enabled at roughly the same time periodically: e.g. oversampling 4 separate inputs...
Hello,
I have nrf52832 dev kit and the device. I try to make smaller code size and setup Optimization Level 2 for size.
BLE works, but when connect by NRF connect and...
Hi,
I am currently developing a product which is supplied with battries (chip is nRF52810). Under normal conditions, the product goes into system OFF mode in standby, it...
Hi,
I'm testing a custom board, based on nrf52832_xxab SoC, with a SWD interface. The board was working fine, but suddenly the debugging interface stopped working. Any idea...
I am curious whether there is a correlation in distance between different devices in a BLE connection.
A picture is attached to describe the situation.
A sensor-board...
Hello dear support team, We are in the process of designing an enclosure for our device. The enclosure is going to be molded and we would highly appreciate your support to...
My requirement is to send from Controller Device to NRF Ble Device through UART of 40Bytes at the rate of less than 1ms. Currently I am using ble_app_uart example as a reference...
Hello,
I am working on the ble_app_template example, nrf52840, SDK 17.0.2 and Segger Embedded Studio version 5.34. I have added multiple custom services to my code, however...
Hello,
as part of my project of wearable solderless modules, I've packed the nRF5340 to the same 20x20 mm form-factor - it was described earlier as part of the https://devzone...
Hi,
We have the nRF52811 in QFN48 fitted to a number of products, with the chip showing 'QAAA0 1850AA'. Does this mean that it's an early Revision 1 ? The Errata in the...
Hello,
I'm new in the Nordic sphere and I'm starting in embedded programming. I was confronted with the following problem and I will try to give as many details as possible...
Hi,
got a question about UART and maximum bytes it can receive in one burst or "packet".
Using nRF52382 and SDK16.
Recently I've been developing a new app in which UART...
Hi Nordic Team/public users,
Request your assistance for troubleshooting the NDK-nrf52840 board that was having a detection issue whereby my laptop/PC was unable to detect...
