Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi
I did test two sample code with nrf52DK kit in segger embedded studio. with sdk ,nRF5_SDK_15.3.0_59ac345
1) ble_app_uart (I connect one sensor with UART,I did some...
Hi,
we are progress of designing custom board using nRF9160.
By reading nRF documentation, my understanding is GPS circuit in Dev kit is unstable/nonperforming.
Could...
I'm compiling a custom application using the CMake scripts in the nRF mesh SDK. The first time I flash to the nRF52832 a SIGTRAP occurs on sd_softdevice_enable. I cannot continue...
Hi all
nrf52840 Development board,sdk is nRF5_SDK_15.2.0_9412b96 ,PC is windows 10
When I run the demo of b le_app_hrs on my development board,I use nrf connect app to...
SDK 13, softdevice 132
function fds_register results FDS_SUCCESS
by calling the function fds_init debugger stops, see comment in function below, and i see "unknown...
Hi
I'm a total beginner here and I have the gyroscope sensor LSM6DS3 and I have the nRF52 DK
I want to read the sensor's data via I2C (i.e. using SDA and SCL pins) using...
Hello.
This is becoming a very serious issue for me. When I program the nrf52840 dongle and when I switches on the power, it automatically goes into bootloader mode, means...
I purchased a sparkfun breakout board ( https://learn.sparkfun.com/tutorials/nrf52832-breakout-board-hookup-guide and schematic https://cdn.sparkfun.com/assets/learn_tutorials...
I'm compiling a custom application using the CMake scripts in the nRF mesh SDK. When I debug the application, even though the debugger is working – I can pause execution ...
I am trying to modify the central / peripheral relay example to not use the HRM and RSCS services and to use my own custom service instead.
I am following this tutorial...
Hi
I have the nRF52 Development kit and I can program it using SEGGER Embedded Studio IDE without problems. However, when I try to program it using nrfjprog, the Dk doesn...
Hi to all, I'm developing a new device that should be a multiprotocol: Zigbee (as coordinator) and BLE peripheral (with his own GATT) There is an example for this integration...
I asked a question on here couple of days ago, but I resolved that issue and have stumbled into a more concise and in the right direction. I am using ble_app_uart as my code...
I am using ble_app_uart as my code base. I included FDS.c and FDS.h when I compiled, it presented many config errors. I compared the two config files for the FDS example and...
Hi,
I have some problem about Keil hex output file.
At the end of hex file, there have some line as following image.
In (a) of above image, why "hex file" need to...
