Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’. Currently it is SystemON mode. But I need to change...
Hi,
I am having trouble running the ANT+ examples on the 15.3 SDK. I'm testing on a NRF52832 DK (PCA10040) and I'm trying to get the ANT+ examples working on SDK 15.3, in...
Hi everyone
I was testing the bonding with MITM settings. I used the code from the following link: github.com/.../nRF51-ble-peripheral-bond-handling . I tested the bonding...
Is it possible to generate a pre compiled library that configure at run-time new BLE services and characteristics on the nRF52840? If the answer is yes, is it possible to...
Excuse me, I have a question on calling external function.
board using: nrf52832
softdevice using : s132(6.1.1)
The situation: There are two applications which is...
Hi
I am using PCA10040 in order to develop nrf52 firmware. For now I would like to try to measure current consumption.
Is there any couple of pins on the board I can use...
I've been doing some testing with the nRF52840 (I purchased the Raytac MDBT50Q-1M), and I'm seeing a pretty hard startup surge. I've attached the results from my scope. The...
Hello,
I have some problems when running the development kit. It seems the problem might be somewhere on the PCB, something related to power sources and power distribution...
Hello,
I try to make my NRF52832 communicates with a memory (MX25R1635FZUIL0) in SPI.
When I try to read the memory ID, the RX buffer is fill with 0x00. But when I observe...
Am facing issue when am reading data from controller(UART) and using ble_app_uart example code to send data to BLE.
Not able to use two uart's at a time.
My setup: nRF52832 with nRF6707 on top. My embedded application synchronously exchanges UART messages with a desktop application that feeds it data (on demand from embedded...
I use nRF52DK as a central using ble_evt event BLE_GAP_EVT_ADV_REPORT to get RSSI from the peripherals when they are advertising. But once the connection is established, how...
Dear community,
I'm having some trouble configuring and adding subscription addresses to one of my node's Generic On Off Server model. This devices is composed of the usual...
I am new to GATT services and characteristics. I have written one custom service with two characteristics for my custom board. I have used nrf 52832 with sdk 15.2.0 and referred...
Hello,
I am trying to connect to my nRF52832 through J-Link v6.22g. This version doesn't contain the RTT Viewer GUI, but instead I am trying to connect through the RTTLogger...
