Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
software: ncs 2.5.0, zephyr\samples\drivers\counter\alarm
hardware: nRF52840dk
Step1: main.c is not be r evised!!!
Step2: prj.conf like this:
Step3: overlay file...
Hi Nordic Team,
I am currently working on a project that involves two devices, both using the nRF52840 microcontroller.
Current Setup:
Device A : I have successfully...
hello Nordic
we are working with ncs v2.5.0 trying to migrate to 2.7.0
1. so that there is several rcs, should i take v2.7.0-rc3 or v2.7.0 ?
2. while choosing v2.7.0...
Hi all,
I wonder if nrf9160 has a built-in temperature sensor interfaced with the ADC, that could help to diagnose the internal chip temperature?
Thanks.
I would like to use the Power Profiler app (with PPK II) as a pure coulomb counter for accurate long term (> many days) cumulative device energy consumption without saving...
Hi there,
We have a product running on nRF5340 with an existing workaround that was carried over from an nRF52840-based product, where SAADC readings are prevented from...
Hi Nordic Team, I'm currently working with the nRF5340 Audio DK to broadcast multiple streams, where the receiver can select which stream to listen to. To the reciever, this...
I have an ILI9340 connected to an nRF53 and want to use LVGL in Zephyr (NCS 2.6.1), but I got no label, etc. showing up. Instead, the display is showing a white screen.
...
Hi, I would like to interface an Alliance NAND flash to NRF5340. The flash supports SPI interface. Which set of pins will be a better choice and why ?
I am planning to use...
Hey Everyone, I am new to Nordic and zephyr. I would say I am a beginner. I am trying to setup custom drivers from ST for the lsm6dsv16x sensor. I know most of the time is...
Dear Team,
I installed segger embedded studio in my PC for working with nordic nRF52840-DK. After that I downloaded the nordic license and it was activated.Perfect. -...
If you Edit your build configuration and then add and argument using this button:
it doesn't seem to work. I've tried doing File->Save and using the Build Configuration...
As recommended by the documentation I am using the malloc/free in the common libc branch.
This code (in zephyr/lib/libc/common/source/stdlib/malloc.c) uses sys_heap_init...
I'm trying to increase the SPI speed to drive a DAC that can go up to 50 Mhz. I'm using an nRF52840 DK and SDK V17.
Even if I can set up SPIM3, there is a limit I need to...
Currently I am failing to make my two NRF24 modules communicate, to make sure the two modules weren't at a bas angle to each other to communicate I picked up and rotated my...
