Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello,
I am currently using an NRF52840 microcontroller (powered at 3.3V) to control two IR LEDs (powered at 5V) via an N-MOSFET. The GPIO pin that controls the N-MOSFET...
Hi,
I prepare my custom board on nrf5340, and i have to use 3xUART, 1xI2C, 1XSPI.
Regarding product specification, i see i cannot configure more than 4 (UART,SPI,I2C)...
Now,I have a project writed by nRFSDK17.And I want to rewrite it by NCS.
I hope to get a module like peer_manager to manage paring and bonding,and I can distinguish connecting...
The status of Docker support is not clear to me. Does Nordic provide a docker images than can be used on Apple Silicon and Integrated with Visual Code Studio. I see a lot...
Hello developers, I am using nRF5340dk as my nodes and my gateway also. (3 boards).
Requirement:
i want to send my data from the board(1) to gateway with the help of mesh...
Hello,
I'm trying to configure the internal temperature sensor but have no idea ...
My board selection is raytac_mdbt53_db_40_nrf5340_cpuapp and, on nRF Kconfig GUI, I...
Hello, I am working on developing a special "serial recovery" mode dfu function of nrf52833 with ncs SDK V2.3.0. Now I encount a problem when adding the following code in...
I am attempting to get the BMI270 sample working on an nRF5340DK, using nRF Connect SDK v2.4.2, after successfully build and flash the program to nRF5340DK I got error "Device...
Hi all,
I am developing an application for a custom board using the nRF52840. I need to use the reset pin (P0.18) as a regular GPIO, configured as an input with an associated...
nRF5_SDK_15.0.0_a53641a s140 nRF52840
Documentation says that both ble_adv_fast_timeout and the ble_adv_slow_timeout are in units of 10ms, and that appears to be true of...
I have read some of the Asset Tracker documentation and noticed there is a nice implementation for operating LEDs in the UI module. This seems straightforward for GPIO control...
Hi,
We're having a problem that our application will hang when using the 32 kHz RC oscillator in the mcuboot bootloader and the Zephyr application. We encountered this...
hit there,
i am trying to work with the NRF5 SDK ARMGCC, in the IDE options a ARMGCC folder exists with an .ld file and makefile. i run the make and get the following error...
Hi,
I'm aiming to develop a custom two-wire serial interface (TX, RX). To achieve this, I'm planning to implement output capture for TX and use GPIO interrupts for RX. For...
NCS v2.7.0 and sysbuild system.
I'm looking for some clarification about Secure Boot and implementing a custom signing command.
What is the difference between secure boot...
