Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello,
I am using an nRF54LM20DK with nRF Connect SDK v3.1.1 and I am unable to establish I2C communication with an external DPS368 sensor.
The application starts correctly...
Hello Nordic Community,
We are currently using the nRF52840 DK for BLE testing and controlled BLE interference generation in a lab environment, primarily in the 2.4 GHz...
I have an ICD configured Matter device, using LIT.
I have added the UserActiveModeTrigger attribute and configured it to PowerCycle and ResetButton.
I can commission the...
I am working on an nRF52840 where I need the following outputs:
a continuous 1MHz master clock
a 126 bit serial bit data output sent out whenever a user wants with a...
I have an application with the nrf52840 that was trying to port to nrf54l15 using ncs 3.2.1 but i ran into various issues. I decided to look into some samples that could help...
I am trying to program a Seeed Xiao nRF52840 Sense with a nRF5DK-52832 using the Debug out P20 connector. I am an experienced embedded systems developer (ESP32, ATTiny/AVR...
Hello,
I am developing Channel Sounding related features using nRF Connect SDK (NCS) v3.1.1 and the nRF54L15 Development Kit (DK) , based on Nordic’s official hci_uart...
I'm using custom board based on nrf9160 SoC. After migrating from SDK v3.1.1 to v3.2.1 two issues (but they are likely related) began to happen:
Battery measurements started...
Hi,
can i ask how do i send sensor readings from BME280 , SGP40 & SHT40 to nRF cloud. i has installed nRF Cloud gateway app ( Android) but it keep loading. So i am asking...
We are working with a custom nRF52840 PCB and would like guidance on the correct and supported way to build a firmware equivalent to the radio_test sample on the nRF52840...
I am working with nRF54L15 running Thread CLI . The device is successfully commissioned to a Thread network and communicates through a Border Router (BR) . SDK version V3...
I am implementing the production line frequency trimming step for the nRF7002, as per https://docs.nordicsemi.com/bundle/nan_043/page/APP/nan_043/xtalxo_freq_trimming.html...
Hello,
Is there any documentation on setting up VoIP on the nRF91x module with Zephyr?
As the nRF91x does not have a built-in VoIP app layer, I can assemble the hardware...
I have downloaded the nrf SDK v3.2.1 and i am testing its BLE sounding reflector and initiator sample code on two different xiao boards here is what i am getting at the serial...
I am using an nRF52840 DK (Version: 3.0.1). After a failed update/event, the DK is no longer recognized by my OS (Windows) via USB. LED5 blinks once when the usb is connected...
