I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hello Sir,
I am working on direction finding. I use the nRF52840 DK to flash the code onto an nRF52811 (custom board) that supports direction finding. In the build configuration...
I was trying to receive some data using "i2c_transfer" then continue the receiving without starting a new transaction.
Stop bit was sent if I configured to use it or not...
My project has a nrf5340+external flash, and an external USB-C connector. The device exposes a USB file system (FAT) which is hosted on the external flash partition, and appears...
Hi Nordic
Q1.
HW: nrf9160 customer board. One USB-to-RS232 cable is used for PC sending AT commands (UART2).
Another USB-to-RS232 cable is used for PC collecting modem...
I am currently evaluating the Nrf54l15 viability for a migration from the Nrf52 for our products. I've been able to advertise, scan and connect with success but I can't find...
Hi,
I'm trying to build the nrf5340_audio/broadcast_source application. I'm getting the following error: nrf5340_audio/src/audio/le_audio_rx.c:20:22: error: 'CONFIG_BT_ISO_RX_MTU...
Hi, I have recently created a board definition for our nRF5340-based hardware using the "Create a new board" feature from the nRF Connect for VS Code plugin. I'm using SDK...
Hello,Nordic team
I am programming with nrf52833 and ncs v2.9.0
I am going to do dfu not by YOUR example(FOTA or UART……)
I flash_write() data to image-1 address，and...
Hello,
Very new to Zigbee. Trying to use nrf 5340 dk as a Zigbee Coordinator to connect to a Thirdreality and a Sonoff PIR motion sensor. No modification (expect adding...
I am using the solution for this exercise to have MCUBoot use the nrf5340dk's external flash for the secondary partition in my own project. I have done the following:
1...
Hi,
I have a question about official suported Bluetooth version on NRF5340, becase there's some conflicting informations.... On this link, it's written " Bluetooth 5.4...
I have nrf52840DK less than 6 month. It has been sitting in my drawer and has some sample code in it which is detecting button press and light up corresponding leds.
Last...
Dear Nordic Team,
We just started the development with NRF54L15 EVK and fabricated and Assembled PCBs as well using NRF54 MCU.
In our product we require 4 timers peripherals...
Hi,
We are currently using the NRF52832 in one of our products. Due to software requirements we need more RAM. Therefore the product is going to be redesigned for the NRF52840...
