I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi,
I am developing an embedded solution where I need to use a nrf52832 as bluetooth controller to detect advertisement packets from beacons. I flashed the zephyr hci_uart...
SDK version 1.7.1
I am working on a project involving a nRF9160 and the sample application nrf/samples/nrf9160/azire_iot_hub and working on reliability issues with disconnections...
Hell to all,
We are currently developing a device that are NRF52832 based on NRF SDK v16. It is in our plan to make use of the Wirepas stack too. At the beginning, it...
Hi
I have committed myself to building a central app that will be based on UART example replace an existing BLE soc that can no longer be found using the central.
My sensors...
hi
i am working on custom card in which nRF52832 is used.i am facing issue with advertising if i uncomment uart_init(); .it does not advertise if i uncomment uart_init(...
Hi,
I'm using S112 nRF52805 as the BLE Peripheral, and Mobile App as the BLE central.
So far, It's no problem to send data from peripheral to central. Could I send data...
Hello all,
I am workiong on nRF52833-DK evaluation board to implement our custom developement.
Using Generic OnOff light switch server and light application, I am transferring...
Hello,
I ran the throughput example ,but I found that setting the MTU size actually requires calling the bt_gatt_exchange_mtu function, which is different from sdk16.0 ...
Hi everyone!
I'm working at ble multilink throughput, and the basic info shows as follows.
chip: nRF52832(one central and eight peripherals)
sdk: nRF5 SDK v17.0.2
...
I am getting below error when editing dfu secure project as the baseline
/nrf_crypto_allocator.h: No such file or directory
the project is modified as below
<folder...
Hello everybody
With me is nrf52840_dongle that am using for wireless communication together with the protocol enhanced shockburst. To increase the signal range, am thinking...
Hello guys. Here with me I have both nRF9160-DK, hardware version 0.8.3 and Thingy:91 boards. I am on the nRF Connect SDK tag 1.2.0 and have nrf9160 SiP modem firmware updated...
Hello,
I have been searching in DevZone and looked at the nRF Connect SDK documentation but I am still confused about a thing: I have developed a BLE Mesh device and I managed...
Hi!
I'm using nrf5340dk development kit to program and debug my own custom nrf5340 board. Everything works and I can debug the code with SES but I can't see the RTT logging...
My application is a Central using SD140.
The connection to the peripheral is made successfully. What event will I get when the Central successfully writes to the connected...
