Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I don't think this is possible at the moment but worth putting it out in the wild:
Currently the binary image sizes for nRF9160 using Zephyr can get quite hefty. Is there...
Hi All,
I am looking for some working example/reference nRF Mesh project where I can get the temperature and humidity values from Thingy device. If someone can help me out...
I trying to connect with ble, i was setup MyBleManager extend BleManager and initialize with the default values it requires but i haven't declare and add UUID in BleManagerGattCalback...
I'm trying to set up the Dongle pca10059. I'm using the softdevice 140 and segger studio. The code is from the SDK, the template example.
the main.c:
static ble_uuid_t...
Hi,
I would like to know if there is an event from peripheral side to indicate that the discovery process is over.
The gold is to disconnect from the central if all the...
1.Would you please confirm the maximum ripple range that nrf52832 can accept for VDD (3.3V) and dec4 (1.3V) power supply, that is to ensure that the function will not be affected...
Hello,
I have used the Nordic Thingy application, I also used the Raspberry Pi Python interface and I observed the temperature measured.
The temperature is not stable...
I have a customer requesting any version above 0.8.5 for part number nRF9160-DK.
Can you tell me what date codes would have the requested versions?
thanks,
Russ
QB79869...
I'm looking for a low energy communication method for a wireless PIR motion sensing device. The system will be battery powered so RX current draw is particularly important...
We are revising a design using the NRF9E5, we are experiencing problems with the third harmonic when configured for 915MHz band, the higher we go up the band the worse the...
I am looking to build a custom board using nrf52840 and want both UART and flashing capabilty on the custom board. I have a NRF52840dk that I will use to program the custom...
I want to increase the pull-up resistor value to educe the current consumption.
but, I am afraid that the GPIO input will not be recognized as High.
I want to know the...
Hi,
I can't find this information anywhere in the AT command manual or datasheet. What is the accuracy for " AT%XTEMP?" and "AT%XRFTEST=10,1,0"?
Kind regards,
Thoma...
Hello,
I'm trying to generate project to realise new user-cases with wireless mesh networks.
I did a demo with the Thingy52 at flower greenhouses
They are very interested...
HI! I've done the basic Blinky and UART examples, and now have to move on to programming something on my own. ( I have to send EEG signals from one BLE board to another/notebook...
