Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
Hello, I am using the nRF52840 dev kit. I am using SES to develop the code for it. I want to include the bosch bme680 library in my code. It comes as a libalgobsec.a file...
The objective is to have a device which constantly advertises some status information - this must be always visible to any Central in range.
The device may connect to at...
I inherited an active project with regrettably little support from the previous developer.
I have been trying to download a copy of the application firmware that I generated...
I try, DFU by USB-SERIAL on NRF52840-DK. I installed SoftDevice S140 V6.1.1 and open_bootloader/pca10056_usb (SDK15.3) Python2.7.16/nrfutil for windows was installed. My DFU...
I am trying to keep an output pin asserted while I jump to the DFU on the 52840.
We have a dead-man switch hooked up to pin 19. I need to hold this pin high while I jump...
So we are using NCPTransport from nrf-util (nordicsemi/thread/tncp.py) to have CoAP connectivity over Thread NCP from Raspberry Pi to other Thread devices. We have a use case...
Hi,
I am trying to install pc-ble-driver-py pypi lib into custom yocto setup. I have created recipes for it which is shown bellow
in python-pc-ble-driver-py.inc
...
Hi. Im working with an application that uses the s110 softdevice and i want to use the s130 to be able to recive advertisereports but when using the s130 Everything stops...
Hey everyone,
I've got an nRF52840 DK on my hands. There's an interesting crash occurring when the return value from ble_nus_data_send() is passed to APP_ERROR_CHECK()....
I am using several Laird BL652 units on a project. They contain a nRF52832. For the most part they are working great, except I have one that only works some of the time and...
I have been trying to use the new GPS example, however, I could not get any location from it yet. It seems that after 30 tries, it stops working (time-out problem). Should...
Hi all,
I'm starting developping code with SES, on an nRF52810 (192kB of Flash), with the BLE stack S112.
Because my project include BLE and custom UUID, I started with...
Hi
I am using the nrf53832 dk.
In the nus example once the data is received from the phone(central) I want to write this data to the flash. I referred to the fstorage...
