Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi ,
I am working on application in which I am using GPIO pin to detect interrupt. GPIO pin normally has logic low level. When it becomes high level I have to generate...
We develop BLE server application on nRF52840 with SDK 1.5 using nRF52840-Preview-DK.
The application is built as multi tasks with freeRTOS where BLE is one of the tasks...
Hi,
I am using Keil uVision 5 and SDK 15 on nrf52840 development. NRF_LOG_ENABLED is set to 1 in sdk_config.h
But NRF_LOGS are not being printed in Debug(printf) viewer...
Hi,
when the micro go in: idle_state_handle(); I have 2 possibility:
If the soft device is present use the first instructions else the second.
This is correct, but...
Dear nordic,
I have an BLE application which works as Central and Peripheral and also which contain ADC,UART and GPIO's
Scanning and advertising controlled by application...
Hi Team,
We have observed that without power supply we are seeing 1V power at board Vcc. Without giving power supply to board.
Why is this happening?
We measured GPIO...
I was trying to verify boot loader using the provided script. I noticed following abnormality.
--It often fails to verify and show the following error:
Reading UICR...
Hi
I'm running nRF52840 MCU at 1.8V, and trying to use the dev kit (PCA10056) to program the external nRF52840 MCU.
According to the datasheet, the dev kit runs on...
Dear employee
for bug 89，
According to <nRF52832_Rev_1_Errata_v1.8>
It is mean below?(spi with blocking mode)
But I think it should be this
when transfer...
Hi Support ,
I'm estimating the average consumption of nRF52840 chip .
Regarding the BT consumption , I used the Online Power Profiler an got the results . But these...
Hello everybody, I've got some of nodes for the light switch example. I'm working on nRF52832 chips. I tried to find answear for my questions, but i didn't. I want to create...
Using the nRF52832 device with the S132-v3.0 soft-device (s132_nrf52_3.0.0_softdevice) and SDK version 12 (SDK120200F12) (Customized for our application, which includes use...
Hi, I need to read a pulse signal with the nRF52840 . I tried to use the timers but it seems to go in conflict with the I2C that I use to communicate with another device....
Hi,
I am trying to make a simple function for writing via SPI. I am using the SPI example and it works fine. Now I would just like to make two SPI functions that I can use...
