I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hello
I am trying to move an arduino project where I read an ADC value from a FSR sensor. In arduino the FSR is powered by 5V and has 10Kohm pulldown resistor. The board...
hi,everybody
I want to design a sniffer for 2.4G raw data,I have some problem below
1.How can I set the radio register to recieve all message on same frequency;
2.I...
I want to create a PCB circuit withe the nRF52810 Transceiver. If you do not understand what i have in mind:
http://si.farnell.com/nordic-semiconductor/nrf52810-qcaa-r7...
We are seeing a potential issue with a product. on start up a pin is read and the read value determines if we go in to a test mode. Pretty standard.
Our failure is during...
Hello
i just bought my DK-nrf52 to move to BLE after playing few months with arduino. I have connected various nrf52832 shields from China (from Holyiot 17095, which is...
Hello, I want to test Round trip delay using BLE MESH 2.0.1 Light Switch Example Code...I have modify simple on off Light Switch Example. Example test using two Development...
Scenario:
We have three verticals in our project. The nrf51822 based device, base station (BS) and server running on cloud.
Problem Statement:
I need to continuously...
I have downloaded "nrf5_SDK_for_Mesh_v2.0.0" yestoday, and try to setup the "light_switch" demo with 3 pic nRF52 DK.
According to the document description, “proxy_server...
Hello,
I have a query regarding the implementation of multiple user-specific GATT profiles in our application.
For example, can we add two profiles like Heart Rate Profile...
I am migrating from SDK v14.2.0 to v15.0.0 and from S132 to S112 (v6) using the NRF52810. I have mostly everything migrated, but a functionality that worked before does not...
Hi,
I'm trying to use the extended advertising to advertise more than 31 B per packet.
I have been through posts on this forum and the ble_app_rscs example to figure out...
I write a code for read the temperature via BLE. The code is modified from the example "android-BluetoothLeGatt-master". But the CallBack function onCharacteristicRead for...
Hardware:
a. nRF52840 DK baord as client
b. nRF52840 DK baord as server
c. nRF52840 DK baord as provisioner.
procedure:
1. Through segger embedded studio I have...
I am using nRF52832 with SDK 14. My app has bootloader and dfu. Everything was working fine with external crystal. I changed my clock source to RC and used these recommended...