Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hi all!
TL;DR
Is there a way to start 2 timers in 1 instructions ? (or to synchronize them afterward?)
- - -
Background
I need to take 8 timestamps of GPIO edges...
Hi,
I'm using S112 v6.0 with SDK 15.0 on nRF52810. It's based on app_ble_uart example. I have some data to save in flash. I define the address as follow:
#define PAGRE_TO_ERASE...
I want to extend the Thread Cloud Client Example (thread_cloud_coap_client_pca10056) with a peripheral controller. And I am looking at the UART Example (ble_app_uart_pca10056_s140...
Hi,
I will connect nRF52840 with other BLE module (ESP32) and they must exchange data (at first aproximation 20-50 bytes each 1-5 seconds).
I need to acheive lowest power...
nRF52 DK,software is nRF5_SDK_12.3.0_d7731ad,I'm using the example of "ble_app_multilink_central". SoftDevice is "s132_nrf52_3.0.0_softdevice.hex"
The BLE device is advertising...
Hi,
There is a racing issue in file: nRF5_SDK_for_Thread_and_Zigbee/components/iot/background_dfu/transport/coap/coap_dfu.c in function:
Sometimes calculated dalay is...
I'm trying to merge uart example in nrf5 sdk with light switch server example in mesh sdk
but I'm only facing these 2 errors :
when Linking uart_pca10040.elf:
Output...
Hello,
I'm usign nRF52832 with nRF5_SDK v15. I'm using "ble_app_uart" example. I just wanted to know that What is the wake up procedure of the MCU when we call the sleep...
Hi,
I have a trouble trying to start development process on my NRF52840 DK.
Following the instructions
https://www.nordicsemi.com/eng/Products/Getting-started-with-the...
The nRF Connect application can not search the device after I modified the Rx, Tx pin in my own PCB board.Can anyone tell me why?
The UART can run well,but the application...
Dear Sir/Madam,
I tried to add battery service to the sample "ble_app_uart", but the code doesn't send notifications to cell phone. I struggled for several days and try...
Upon my first connection to my device with LE Privacy, first connection meaning after I've reset the firmware, I'm unable to read anything. The write characteristic works...
I am trying to use a Raspberry Pi as a provisioner for nRF52 development kits. I can run the meshctl utility on Pi but I am not able to see the un-provisioned beacons on the...
My application running on top of the S132 has a data base which can store up to 12 hours of data (720 points @6 bytes each). A request is made from the GATT Client to retrieve...
