Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I just update my sdk to 15.0.0, which use the softdevice s132_nrf_6.0.0. but when I try to generate the application package, I found the nrfutil do not give the sd-req code...
Hi,
Where the Firmware is being stored in the flash??
In which address of the flash the firmware is being stored when i flash the code??
In what file type ,the firmware...
Hi.
I am trying to set up a simple Ble beacon on a PCA10040 and a sniffer on another PCA10040.
IDE = Segger Embedded Studio for ARM (This works fine)
The beacon uses...
Hello,
I'm trying to start working with the NRF52832 Dev board for quite some time and can't manage to get anything complex done other than blinking an LED and even that...
We are using a TI AIC audio codec interfacing with the nRF52 over I2S.
The TI codec specifies the following expected clock frequencies for a sample rate of 16KHz and sample...
Hi
We are trying to find a solution to connecting a BLE peripheral to a "preferred" or "primary" central. We are considering having the peripheral connect to multiple centrals...
Hi,
Probably the answer to this question is no, but I can't seem to find any reference in the standard and/or your SDK documentation that proofs that the same relay message...
Hi,
In the Release Notes of SDK 14.2 the following issue (for an emulated NRF52810 project) is mentioned :
*** Known Issues
****************
** BLE **
- When working...
Hi,
Is there any API in Softdevice S132 v5 production to set up advertising extension?
In migration notes of SoftDevice S140 v5 alpha3 I can find annotation:
A new...
I have read the nAN24-13 application note as well as the crystal selection portion of the nRF24LE1 and nRF24LU1 data sheets and I am still undecided about this crystal
https...
Our intention is to wake up the nRFLEI from power-down using the external interrupts, perform some actions and return to power-down. There are three external control signals...
Dear nordic employee
when I use the spim to send 1 byte address to read it's value(4 bytes)
nrf_drv_spi_transfer(&spi,headerBuffer,(uint8_t)headerLength,readBuffer,...
Hi,
We are trying to transmit a single byte over SPIM using easyDMA but our logic analyzer shows that 16 bits are being clocked out. The first 8 are our message and the...
Hi
I just test the new sdk 15.0
When I test the power of the demo project named "ble_app_hrs_freertos", I get the power table below:
No chage
810uA
...
Hello world.
After I have used this guy code.. KNN c++ . and good for implement it to my module nRF51822.
But if there's problem issue or not. because, there was an confusing...
