Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi,
Using S130 via mBed, I'd like to have a fairly large number of characteristics (say 30). Unfortunately this seems to be too many, as sd_ble_gatts_characteristic_add...
I have compiled two projects namely Blinky and ble_app_template.
Both projects run and debug but the radio portion in the ble-app_template is not functioning.
Having a compiled...
I have been reading a lot of post about static pairing passkey using S110. I have tried two example provided in this threads: devzone.nordicsemi.com/.../ devzone.nordicsemi...
Hi,
I have done the bonding and saving context to flash. As an example I used ble_app_template. I cutted all redundant code and limited to single bond for simplicity.
In...
I am trying to communicate between nrf51822 and Android device using Gatt. But nrf51822 invokes UartService.ACTION_GATT_DISCONNECTED after some time, the disconnection happens...
Hi,
until today we develop our application on Nordic DK with nRF1422 with 32 KB of RAM.
We are using S130 and SDK 8.1.0.
Today we saw that our target module, the MBH7BLZ07...
Hi!
I'm working with nRF51DK with s110 soft device on it. I'm trying to write simple custom service which reads some data from sensors and send it over BLE to Android app...
Hello,
I know the current limit of 15mA to share among all gpio pins.
If I source/sink current in very short bursts (100ns every 1ms) can I draw larger currents than 15...
Dear All,
We are working on a custom board with NRF51822.Everything works fine apart from the timer. What we are doing is that once the board is booted, it reads some values...
Situation:
We are building BLE device that have GATT service showing a analog sensor value.
AIN2 is connected to the sensor. AIN4 is connected to battery.
We would like...
Hi.
I use nrf51822 rev.3 build number CEAAE00(0x0079) package is WLCSP.
Before I got a experience already develop wearable device using rev.1 chip. And that board work...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
