Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
When I program an interrupt, the NRF52840 requires 250uA extra. I read something about the sense interrupt, but I cannot find any working example. How should I implement an...
Hi,
I am working with Thingy53 using the ESB (Enhanced ShockBurst) library. I have my basic app running with multi-point comms and power control. This was done without using...
Hello,
We have a product which is a custom nRF52832 board, nRF5 SDK (didn't have time to upgrade to nRF Connect SDK), s132, BLE.
We used to call delete_bonds() function...
I‘m tring to run nRF5340 Audio applications with two nRF5340 Audio boards, following at: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.6.0/nrf/applications/nrf5340_audio...
I'm using the async API for UART and I have noticed that, shortly after initialisation, I receive a single character with the UART_RX_READY event. This character is 0xff ...
Dear all,
I kindly ask you what is such warning that arise in building the configuration for the NCS example, please point me to better understand why arise and the related...
I now have a 52833 board, my question is what is the difference between it and 52832?
Are they very different?
Which protocol stack does it use?
thank you
Hi
I can't find any info regarding a cut off feature for the nPM1300 if the battery voltage is to low.
we are using a battery with PMC but that is meant as last resort...
I am using nRF52840 boards. I have one query.
I understand from your documentation that MPSL schedules the Radio driver to access the Radio. And BT ticker is for time slots...
Hi
I have flashed the unit with the Vysor flash file at Vysor Dongle · koush/vysor.io Wiki · GitHub The unit is now dead and has not recovered so I am returning to amazon...
I was planning on writing firmware for the nRF52840 chip (AKA System Controller) on the NRF9160 DK. Primarily it will use BLE and serial communications over some of the pins...
Hi, I am using nRF52840 and nRF Connect SDK V2.6.0
I want to send 7000 bytes of data using USB at a time. Now I am able to send only 1024 bytes at a time. I modified USB...
I'm using the nRF52+SDK11.0.0+s132. I'm developing a system that streams BLE notifications to an Android app at ~53kbps (40B/6ms). I have the connection intervals set to 7...
Hi,
I have a system I am redesigning to use the npm1300.
It has a rechargeable battery, about 3-4 weeks per charge, connected to an nrf9160.
The current system...
Hello,
I had to build the https_client sample again to compare some behaviors on my application and as I flash it to nRF9160 I am having a cyclical error as below:
...
