Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hello,
I have 9 sensors based on NRF54L15 working as GATT server. I push around 100 bytes every 15ms from all sensors to the central hub. When i connect all nine of them...
Hi everyone!
I am developing device based on nrf25833 mcu which should transmit data to android devices using ble characteristic notification mechanism (data received...
Hi!
Recently I bought this device (v1.1.2) and I was very happy about it until I tried to verify the current and voltage readings. Tried two multimeters and they both agree...
I am porting and existing app to nRF Connect SDK 2.7.0 from 2.6.1. Using sysbuild, MCUBoot and the app are building and I am able to load the firmware onto the PCB and it...
Hello!
I've just come into contact with the nrf54l15. On the customer's board, it is necessary to change the NFC pin to a regular gpio, and they following the previous nrf52...
Hi Is it possible to configure project to use simultaneous multi image DFU and serial recovery over USB? I would like to be able to update both cores using dfu_multi_image_XXX...
I have an LED connected, and I want to use PWM, but enabling it adds about 700 µA of passive current — both when the output is high and low. However, if I set the duty cycle...
Hi,
I'm developing on the nrf5340 and the semtech LR1110. I'm using the latest SDK version 3.1.1.
I saw in the SDK that there's a library for the LR1110, but I can't activate...
Hi.
I try to build the example Matter: light bulb and in the terminal shows an error that iI don´t underestand what is the problem.
Please ¿Any could explain me why ocurs...
Hi,
I am using the Thingy:91X device and can see the updates appearing on the hello.nrfcloud.com web application, but I would like to have access to the 'device' via the...
As the title said, I'm currently on the nRF21540 DK. I turned on Async UART:
CONFIG_UART_1_INTERRUPT_DRIVEN =n
CONFIG_UART_1_ASYNC =y
CONFIG_UART_1_NRF_HW_ASYNC =y...
Hey Nordic Team
Just looking for guidance and clarification on the nPM1300 setup. couple of questions on the sample setup below.
Project Overview
Project is a consumer...
I setup 2 Holyiot nRF54L DK Development Boards with the channel sounding sample code from NCS 3.1.1 samples/bluetooth/channel_sounding_ras_initiator (initiator and reflector...
We have designed a custom board around nRF54H20 EngC revision and testing it on NCS 3.1.1. We were able to do provisioning and bring up using iron-side binaries. But got two...
