Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
nRF54H20DK (rev. 0.9.1), SDK: v2.9.0-nRF54H20-rc2 and the same Toolchain, IDE: VSCode + nRF Connect
We need to implement a multicore application for nRF54H20. I...
Hi,
I have a question concerning time zone support in nRF SDK >= 1.9.1 for nrf9160.
I'm trying to implement an LwM2M client that should be able to convert a UTC datetime...
NCS 2.7.0/2.8.0
mcuboot + MCUMGR in the application for BLE DFU
NRF52840
We have been developing our next version of our product, transitioning from NRF SDK 5 to NCS...
Hi，
When I used NCS V2.5.0,after two devices successfully establish a BLE connection but then disconnect due to a timeout, subsequent reconnection attempts fail with error...
I have a BLE system where multiple sensors operate as peripherals and send data to a BLE central. These sensors enter sleep mode after transmitting data and later wake up...
Hi all,
I applied QSPI driver on NCS 2.4.0 with QSPI LCD panel and I encountered the problem.
The red area is the data I sent, but the blue area is not what I sent....
Hello,
I designed a PCB using nRF52840 for controlling the board.
I have physical access to the following pins : SWDIO, SWDCLK , VSS , VDD , nRESET.
What is the boot...
Hi,
I'm trying to test DTM over USB CDC with an nRF5340DK unfortunately, Direct Test Mode desktop App is not detecting the DK.
Build command (copied from VSCode output...
Hey folks,
i have to use the nrf9160 board to create a PoC for a project of our company. The main topic of the PoC is not important here because i cant even connect to an...
Hi,
We are on NCS v2.9.1
We have an existing project on based on the nrf52832, which we use as a hci_spi controller. There, CONFIG_BT_LL_SW_SPLIT is set. We are now porting...
Hi, I have encountered issues flashing a NRF52833 board which is on a custom PCB. I have picked the project up from another developer so it is somewhat developed already....
hi,
I am reviewing development in the environment below.
* HW : nRF52832
* SW : SDK -> example -> ble_app_uart_c
In the nRF52-DK board, we reviewed the example...
hi support team,
i want to confirm the FEM control when using nrf21540ek for mesh demo "light" with 52840dk.
i set :
CONFIG_BT_CTLR_TX_PWR_ANTENNA =20
CONFIG_MPSL_FEM_NRF21540_TX_GAIN_DB...
Hello Team,
I am trying to set configurations for FOTA. I refer smv_server sample code and the following document https://docs.nordicsemi.com/bundle/ncslatest/page/nrf/app_dev...
We are using the NRF9151 and unable to establish a connection to an LTE-M network in Ireland (testing in Cork currently). We are using a Kore MVNO SIM which supports Three...
