Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hello,
I’m trying to run **LVGL 9.3** on a **nRF52840 DK** with a **2.8" ILI9341 TFT display (SPI)** using **NCS v3.1.0 / Zephyr 4.1 / Toolchain v3.1.0** .
### Problem...
Hello, I want to check the component alignment on the layout.
My layout is different than the reference.
Where should I connect the VNA?
Can I calibrate it on the PCB?
Hi,
I am using a custom nRF9160 board with the nRF7002 Wi-Fi chip via SPI, running NCS v2.9.2 . My goal is to connect to a Wi-Fi network.
However, during initialization...
I want to change the start address of the app in the ESB example from nCS 3.0.2. By default, after compiling and flashing, the program runs from address 0x0. I want to change...
Hi Nordic,
I try to print hello world from promicro(nrf52840).
I am sure board is ok, because I test zephyr 4.2 cdc_acm example on it, and I can see /dev/ttyACM* & console...
Previously, when our NRF5340 was transmitting at a 3ms interval, we encountered issues where the transmission speed failed to meet requirements, with data packets being discontinuous...
Hi Team I was exploring communication with ads1292 over SPI at 1 MHZ. I tried nrf_drv_spi (SPI0_ENABLED in sdk_config.h) api and I was able to communicate with ads1292, however...
I try to do everything as in the guide (second advanced option) devzone.nordicsemi.com/.../small-i2c-oled-displays-using-nrf-connect-sdk but I get errors when building
...
I need to set the connection interval to 7.5 ms. The main.c has the corresponding macro: MIN_CONN_INTERVAL but it seems to me that it supports only integer values...
Please...
When building examples targeting the thingy53/nrf5340/cpuapp board target cmake is run twice, on a fresh build. Then once the build is finished, without modifying anything...
Hi,
In the past we had quite some issues with moist in nRF9160 issues (likely due to bad storage at our PCBA partner). We are now baking all nRF9160 always at 125 degree...
Hi all,
i am currently developing applications for the nrf54L15 for science. We ordered nrf54L15DK and everything is running fine. As we would like to switch to public availabe...
Hi,The Nordic Team
I am developing the Matter over Thread product. I have defined a Bluetooth transport protocol, and now I can receive data. But now I do not know how to...
Hello Nordic Team,
I’m looking to build on a BLE Scanner(Beacon functionality) + Peripheral features on my application using the nRF52810 device, but I’m facing difficulties...
I've been unable to get a SPI MOSI pin to output data on nRF54L15DK using Nordic Connect SDK v3.0.2. SPI transactions report success, and the SCL and CS lines are clocking...
