hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Because the GPS will continue to output data after starting, in order not to block the main thread, I placed it in another thread, but I found that when my main thread did...
It is not clear from the website whether Nordic has produced an LE audio chip/board, and if/when it will be available for purchase? Does anyone have any info on it?
Hi,
We are porting our application from nRF Zigbee & Thread SDK to NCS.
On the ZIgbee side, we have been using this methods:
1. zb_zdo_find_bind_src(): to check...
I'm working on a project that has multiple custom partition manager configuration file that are implemented based on the instructions provided in this section of the partition...
Hi,
yesterday, I met the same situation as here . But now, I can't even see one log, even after I annotated the code related twi and just remained some “NRF_LOG_INFO（）”...
Hi,
I am using SDK 17.0.2 for a simple scanner project, where nordic SoC is communicating with main MCU via SPI. The code starts normally on nRF52832, but on nRF52833, it...
Hi,
I am running the example ble_app_att_mtu_throughput with the nRF5 SDK on two nRF52840-DK dev kits. I have flashed both dev kits with S140 soft devices prior to flashing...
We are finalizing a product that has a BL652 (nRF52832) in the main unit and a BL651 (nRF52810) in a remote control unit. We are trying to get our regulatory radio testing...
When I changed HFCLK from "64 MHz internal oscillator (HFINT)" to "64 MHz crystal oscillator (HFXO)", the power consumption when executing sd_app_evt_wait() became larger...
Hi,
We've created a FW image targeting a PCA10056 which consists of our application FW, the example secure DFU bootloader over USB, and the softdevice. Everything works...
I have the ws2812 example working with ncs v1.5 on board actinius_icarus_som
However, when I combine it with other code such as for a custom SPI device and udp comms it...
Hello,
I contact to you because a customer is interested on the RF System, part number nRF5340-QKAA-R, and they asked the following below;
"
Customer wondering if you...
I added FOTA_DOWNLOAD and MCU_BOOT to my project.Then I want to use http to download a file, and an EBADMSG error occurs at this time.
I reproduced this problem in the download_test...
We have an I2S implementation that I based on the example code, but using the nrfx driver. Audio plays fine, but after I call nrfx_i2s_stop, I first see that no next buffers...
