Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello,
I would like to know if it is possible to not use softdevice because i need more flash for my code. I guess it is possible but when i don't enable softdevice in my...
Hello,
i'm trying to use SPI with nrf9160DK as master and RFM96 module as slave. At the moment, i'm developing elementary functions to write and read from my slave device...
Hello
I am working on Nordic nrf52832
I am using the "ble_app_blinky_c_pca10040_s132"
I want to use ble for scanning a beacon (eddystone TLM) and collect its data. ...
please help. I need functional description of what is need step by step for doing a zigbee hardware device switch and management over bluetooth on the thingy52, i have all...
Hi Team,
We are using the NRF52840 with s140 Soft device for our BLE application.
While we are facing some issues while doing debugging.
1. We are getting Hard Fault...
Are there any issues of pairing a nRF52833 using OOB pairing with a IOS device? Is there a good example code I could start with?
Thank you very much.
All the best
P...
The system requirements: 50 identical nRF53-based devices (each with a sensor and an actuator), positioned within a 3x3 meter square should be connected to a single computer...
Edit : The code posted below works on the 96x96 3V(LS013B4DN04) variant of the display, I still have no idea why it doesn't work on LS044Q7DH01, but I'm guessing it doesnt...
Hello!
I have some devices with a custom built PCB on my desk, all of which have my own custom firmware on it.
Sadly the devices don't have access to the debug pins...
Hi Team,
May I know the functionality of the below mentioned signals:
MIPI RFFE interface pins: VIO, SCLK, SDATA. MAGPIO interface pins: MAGPIO0, MAGPIO1, MAGPIO2. ...
Hi,
I got a question on nRF52832 platform. When it is brand new (so without loading any of our FW) and powered through 3V3, it draws up to 4.6mA when powered. But we also...
Hello,
We have seen the below error,
NRF_ERROR_INVALID_ADDR If the EasyDMA is used and memory adress in not in RAM.
While trying to connect with an external sensor hub...
Timer A with a 10-minute interval, timer B with a 4-hour interval, and timer C with a 10-second interval are required, and A and B should also run out of time in low power...
Are there any updates on coded phy support for the nRF sniffer?
I found a thread about this from "over a year ago" which says to check back in 4-5 weeks: https://devzone...
When CENTRAL connects how can I read the UUID and ADDR of the peer?
static void ble_evt_handler(ble_evt_t const * p_ble_evt, void * p_context) {
switch (p_ble_evt->header...
