I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hi all
We are using nRF9160 DK & want to test its MQTT library by uploading some data to the broker. But, my city doesn't have LTE Cat-M1 / NB-IoT network.
Can you suggest...
Hi,
1. ZigBee Cluster Library Specification(Rev 6) -> 3.3.2.2.3 Battery Information Attribute Set -> Table 3-18. Attributes of the Battery Information Attribute Set tell...
Hi,
I am a beginner to nrf9160.
I already can do send the large data to server. (Maybe not too large just about 15KB)
In my test, I will send that data in every 25 minutes...
Hi,
I am not able generate dfu_package.zip using nrfutil.
I am using ubuntu 18.04, and python2.7 is installed is default python version.
I get the following error when...
Hi!
I have bought the Thingy:91 and in user guide (on page 12) it says that the nRF91 DK should be used to update the modem firmware, further more, it seems like it is only...
Hi I am trying to program the bsp buttons on the NRF52 DK, so pushing button 1 will toggle start advertising and going to sleep by calling sd_app_evt_wait().
I have successfully...
Hi All
I'm trying to use the Adc in Sample convert mode: "nrfx_saadc_sample_convert(0,&ADC_Val);" to sequential read two ADC pins .
I have used the code below to init...
I want to add a node(server) in multiple group in Mesh.
Application is if any switch pressed next two corresponding light to be trigger to on. for that one server subscribe...
Hi,
We are using Mesh successfully with the Mesh SDK 3.1.0 combined with Nordic SDK 15.2 and Softdevice 6.1.1.
Due to the nature of our BT device I would like to explore...
Hi,
I am new to the nordic platform .I am using. BL652 modules .I was able to blink my on borad LED and then made the device as peripheral to advertise with the device name...
I'm using the nRF52832 with softdevice s132 and SDK14 with ARM GCC
I'm trying to set up the SAADC peripheral to read battery voltage, and I can get everything working as...
Hi all, We use a kind of widely used nrf24l01 module in our product developement.It use the nodic's reference design of nrf24l01 with an external pa/lna.TXEN and RXEN of the...
Hello! I have an Android phone and nRF52840 as a peripheral. Now I want the peripheral to have a whitelist with exactly 1 peer with whitelist being dropped at button press...
I read in many blogs that I can use access layer directly without models to communicate .
So access layer is under mesh?
means that can i send data to remote node(out...
