When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hello,
I have merged nrfx_spim and ble_app_uart. I was testing the spi tx function as my application has specific timing requirements. I have experienced something that...
chip: nrf52832
sdk:nRF5_SDK_15.3.0_59ac345
my purpose: i want to store data to flash from ble_uart
demo: examples\ble_peripheral\ble_app_uart and examples\peripheral...
I followed strictly all steps of the nRF Connect SDK Getting Started Assistant. However, the code doesn't compile:
(...)
9> Compiling ‘reboot.c’ 1> In file included from...
Hi, i am working on a bluetooth application with the nRF52832. When i try to connect a Samsung Galaxy S8 (Android 8.0) via nRF Connect, i get a LMP TIMEOUT error after 40...
Launch, then select 'Launch Programmer, tool displays message "The app only supports nRF connect ^2.5.0 while your installed version is 3.0.0. It might not work as expected...
From what I could see the Asset_Tracker example works in LTE, not in NB-IoT. How can I test NB-IoT?
I would like to get some hint on what example to use and what to do to...
Hey all,
I'm a bit lost here... I developed a wireless sensor for a customer based on the nRF52840 and it works great. Now we're developing a small light weight gateway...
Hi everyone,
I'm trying to developp a MIDI USB class compliant device with the nrf52840 DK.
I'm beginner about USB developpement and I have only basics about MIDI class...
I am using SDK 15.3.0 working on nRF52832, on windows platform.
Our requirement is, we need to get the data from both nRF52832 and BLE Heart rate sensor at same time and...
I have developed a new board based around NRF91 module. Ten prototypes are produced and six of them work. Other four devices cannot connect to the LTE network. I am using...
Hi,
I'm using nrf_serial to configure and then read data from a GPS engine, but I am getting unrecoverable OVERRUN errors on start-up if the GPS device is sending data when...
Hello
the setup is a nrf52840, the sdk15.3, Softdevice s140, apps: open bootloader and blinky app
Is there a way that the DFU mode is always there, at the moment its only...
Hi,
We are in the HW verification stage of a product with an nRF52 series MCU. We were easily able to measure the 32MHz XTAL accuracy using the buffered output feature;...
Hello, Dear Support!
From the DevZone I downloaded ntf5-multilink-example-master. Here . Thanks for developers. The solution in SES was built and uploaded without any troubles...
I am using 'Segger Embedded Studio'. While changing the settings of a project in options, why we select Private Configurations (common)? I have seen this procedure in many...
