Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
So I'm kinda new to micro controllers and I followed the steps for the custom service tutorial ( https://github.com/bjornspockeli/custom_ble_service_example ), however when...
Using the scanner module, I set up a scan filter to scan for UUID with no auto connect. In the scan_evt_handler, I have a switch case for the NRF_BLE_SCAN_EVT_FILTER_MATCH...
I want to secure advertised packets using ccm
I am using s132 , SDK 14.2.0 and nrf52 dk
I found that AES-CCM peripheral is blocked by soft device usage and that I need...
I have this error.
In a last time with same error on a nRF52832 I decided this problem with increase:
On the 52832 it works. But on the 52810- project fall.
How to...
Hello,
I am using nRF52832 DK PCA10040 v1.2.4, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
As part of ble_evt_handler...
Hello All,
I am developing a custom board with nRF52832. All good with Segger Embedded Studio, I could download and debug the board successfully.
When I tryed to program...
Hi, i'm using nRF52840
I'm using 2 uarts :
one (uart0) is only for logging and another one (uart1) is for communication.
I can send from both uart, i can see i receive...
Hi
I sometimes get stuck in the zb_nrf52840_abort but the stack trace seams to be strange, its only containing two levels, Am I missing something or is there a better way...
Hello,
I have inherited a Thingy:52 project which was using some old versions of SDKs. Now I am trying to port it to a newer version in order to make it compatible with...
In nRF5_SDK_15.3.0 some undefined reference error reported when using nrf_drv_clock module (example: undefined reference to `nrf_drv_clock_hfclk_release)
The problem is...
Hi,
Is it possible to update the modem firmware once the product is on the field? I'm not talking about the application hosted on the M33, but the actual modem firmware...
Hi,
I'm testing pca10059 usb dongle with pc-ble-driver (not nrf-connect-pc)
I need 2M phy because of throughput.
latest pc-ble-driver support nrf52840 with softdevice...
HI,
i'm using SDK 15.2.0 and MESH SDK 3.1.0.
my program using the uart to get data from a sensor and sending it over the mesh network.
now i'm trying to write to the...
Hi.
I'm using
An nRF52832 DK
SDK 15.3.0
Segger IDE
The soft device is S112
JLinkRTTViewer for debug
I'm using the ble_app_proximity as my starting point and...
