Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
In which state are the configured UART pins if the device is held in RESET for nRF52832?
We want to use the UART to communicate with the host without the nRF52832 in certain...
Hi, I have a project where an STM32 controller has the updated binary file for nRF1822 in flash and it will upgrade the firmware on nRF1822 with the serial implementation...
I am trying to add "Softdevice_handler" to project under nRF52 SDK_15.0.3
But i couldn't find "Softdevice_handler" in nRF SDK_15.0.3 and it is there in SDK 11
How to add...
Good afternoon,
The 'sd_ble_gap_device_name_Set' seems to have a limit of 10chars when defining the device name. In principle, it should be 31. Why do I have this limit...
Hi
I would like to use a 2.4Ghz remote controller for a project but I did not find any example/documentation on how to use 2.4 frequency with my nrf52.
Can someone...
Hi
I would like to use a 2.4Ghz remote controller for a project but I did not find any example/documentation on how to use 2.4 frequency with my nrf52.
Can someone...
nRF52840-DK 2pcs, one TX broadcast signal software, one RX software. RX can receive TX.
My nRF52840 product 2pcs, one TX broadcast signal software, one RX software. RX can...
Hi,
I am working with a motion sensor which sends a message when it detects a motion. I am communicating between the nRF52 DK and the sensor via UART. I am able to receive...
Hello,
I am interfacing nRF52840 DK with the MAX30101 sensor. I am able to execute all the TWI transactions necessary by using port 0 pin 27 as SCL and port 0 pin 26 as...
Hi,
As background, what I am trying to implement is continuous uninterrupted SPI master output from the nRF52840, compatible with the MCP4822 two-channel 12-bit DAC. The...
Hi. I have some question.
I'm using Mesh with nRF52832.
How get address after provising?
Is there API function?
1. get or set address -> Unicast address.
2...
Hello,
I am trying to configure a Heart rate sensor MAX30101 with nRF51822. I have initialized the sensor correctly as I can see the LEDs turn on. But when I read data from...
Hi, guys. I'm trying to work with Opus applications using PCA10056 v1.0. In order to play Opus fils using the nRF52840,
do I need audio DAC + audio amplifier to create sound...
Hi,
I am using NRF51822 pca10028 UART ble example ,
I need to give provision to change the name of the device after pairing and reset the device so that it starts advertising...
Hello,
I m bonding a central and a peripheral and saving the bonds into a whitelist i use at each startup. When i delete the bonds on central side, the connection to the...
